When I use the iPhone app I have 2 options under 'My Devices', 1 has the myGHL icon under the P4 image, the other just has the P4 image, both work.
Regarding myGHL on the communication page it...
Type: Posts; User: tramsden
When I use the iPhone app I have 2 options under 'My Devices', 1 has the myGHL icon under the P4 image, the other just has the P4 image, both work.
Regarding myGHL on the communication page it...
thanks for reply but i have no power cables near the probes that could cause the problem.
Tony
Hi
I can connect to myGHL externally using web browser on work PC
I can connect from home using https://www.myghl.com/GHLConnect/
I can connect to P4 from home using iPhone app
I cannot connect...
11096
Thanks
No, the probe is 2 sump chambers before heater.
Hi
Can you explain this alarm I get occasionally, I hear an audible alarm and email is sent.
Within a few minutes everything is back to normal.
This is the content of email;
Alarm 000: Alarm: ...
Cleared all browser data on safari and chrome but still no joy.
I can even access the menu from left hand side but when I select anything the screen changes to the relevant screen but greys out and...
Thanks Vinny
The DNS address had not been filled in after update, so after I put this in, MyGHL is connecting.
Curiously I cannot get the P4 webserver page to load, the data windows are greyed...
I updated my P4 to latest fw via GHLControlCenter V1118 ( vmware on mac).
I can connect via iOS app without issue but the MyGHL route does not work, the icon is flashing on the P4 display.
I have...
Great. What's your routine for cleaning?
T
Hi
I have neglected to clean my conductivity probe on a regular basis and now it keeps reading low. It does have some white deposit at its end ? calcium.I have read about rinsing it on a weekly...
I'll try that. Thanks
But how do I set up Profilux to turn off skimmer when full
Hi
I have to go in hospital for a few days and need to setup a skimmate collector which will turn off the skimmer when full.
Can anyone tell me how to setup the optical sensor I have to do this,...
Thanks for the reply but I'm still confused because each sensor has 2indicators. They usually have 2 ticks against them when the water level is up to them but I have seen 2 dashes or 1 tick & 1 dash...
Hi
Thanks for the app, works great for me. Just a little query, the level sensor area shows 2 indicators '1 & 2' these are preceded by either a tick or a dash I have seen various combinations. Can...
Thanks Carolin,
If I do this i.e. the manual way, would the program just repeat as it starts the next week?
What I was looking for, was to give the additive over 4 days and then for the program...
Any help on this would be appreciated.
Hi
Read through the manual but not sure how to do what I want to do.
I want to dose 24mls of solution 4 times a day but only for period of 4 days.
Can someone kindly guide me through the set...
Hi
I am aware that its best to protect the doser from humidity but the only place I can put my new doser is in the cabinet where the sump is, I'd like some advise on how to minimise the effect on...
Ok I've upgraded the powerbar to firmware version 1.08 and problem is the same, I'm looking at the values now,
PLC says 0.65A, the status email says 0.1A
Tony
Hi
Why do the socket current information values differ depending on what you view them with.
Web server and status emails tell me that socket 4 (skimmer) is 0.10A, whereas PLC ver 5.1.2.3 tells...
So it's not just me.
It's not all the language that is in German it's just that page. Anyhow I did change language from the profilux, to German then back to English, thought it had resolved the problem because the...
Hi
When I view the web pages from the p3 fw 5.12b I notice that the console page is in Germany and that I cannot change the state the state of the switches, also the lightening button increases...