Hooray! Got it working, was my own stupidity rather than a technical fault, so often the case :)
Type: Posts; User: Techmik
Hooray! Got it working, was my own stupidity rather than a technical fault, so often the case :)
Hi,
I'm having difficulties with an old, but previously working, Profilus PlusII.
I am trying to use the Flash Firmware Programmer, however each time I get a timeout error.
I am using a correctly...
Hi, I have a Profilux Plus 2 running firmware v5.15, the display always reads 'Nominal Value - Selection With' and I cannot change this.
If I press and hold the ESC key the display will scroll...
Thanks for the reply, had a go with this already, tried the CDMv2.12.00 WHQL executable but didn't work. Going to try generic USB/RS232 adaptor as I have one of those working on a win7 64bit on...
Hi, I am trying to connect a Profilux Plus2 via installed PLM-USB card on windows 7 64 bit PC.
There are no device drivers found, anyone know where I can find drivers for FT232R USB UART.
I've...
Hi, I have a Profilux Plus II that has a possible firmware problem.
I have tried the Flash firmware utility which installed correctly, on power up the screen displays 'check ok' up to the Profilux...
I currently have my 'maximum on time' set to 0:00:30 and Reset Error Auto unticked.
The level sensor does switch off the return pump when it reaches low position, I have not tested if it will...
Hi Carolin,
Thankyou for your reply, the settings you suggest seem to work ok.
I have set the switchable socket to 'Fill water (ATO only)' sensor 2 inverted switching
Level sensor is set to...
Hi, I have a Profilux PlusII and I have a float sensor in my sump return section controlling the auto top up.
I have recently connected a second float sensor via the y-cable and I would like to have...
I have checked the buttons, they click when pressed but have no function except to scroll through the setup options (up & down keys), I cannot tell if there is some other problem.
I also have the...
Hi Carolin,
Thanks for your reply, I don't think it is the physical keys that are the problem, they click when pressed also the 'virtual' keys on the remote control on the PC do not work.
Hi,
I have a Profilux Plus II firmware version 5.15.
The display on the controller displays: Time/Date Selection with.. but none of the keys on the controller function.
Connected via RS232...
Job done! 6P6C RJ12 is the cable, love it when a plan comes together, thanks for all your help.:D
Thanks PIWAWT,
Yeah had a rummage on the Bay found the 2m 6P6C for £2, should be plopping thru the letterbox Friday.
OOps 2 posts!!
Thanks PIWAWT, the Knipex one looks like the proper kit (apologies, I'm a bit of a tool freak)
Been on the Bay myself this evening found a 2m 6P6C cable for £2 so I'm gonna try that first.
Will...
Hi Folks,
Thanks for the replies, I think I can try remaking the cable using new FCC68 6P6C RJ11 connectors.
There appear to be 6 wires within the cable, you can see them through the clear plastic...
Hi,
Apologies for newbie question, I need a cable to connect my Profilux Plus II to STDL4-4GB plugbar.
I've established that it is the cable that's faulty, I have 1 new one that works, I have 2...
Seem to have fixed the problem by swapping the Tunze1 & Tunze2 cables around both pumps now functioning.
I will adjust the voltages as you have suggested also.
Thankyou
Hi,
Have a problem, just connected 2 Tunze 6055 to Profilux Plus II with new Y splitter and new Tunze 1 & Tunze 2 cables to L1/L2.
Although I have set both to Permanent-No Waves (for simplicity at...
Gunther, Matthias..thankyou so much for your brilliant help.
I am now PC connected and very happy:D
Now I need to learn how to programme the damn thing!
Great help, thankyou again.
Regards
Mick
Ok thanks got that, now its asking to press reset on microcontroller board, where is this reset?
Oh hang on just read it does it automatically! doh!:p
OK, I'm a little further on..read emergency update instructions. Cannot set Hex File, when I select Open I have no .mhx files to choose from, there are none in the FMC16LX folder, nor can I find...
Ok great, I've downloaded flasher tool FMC16LX.zip what do I do with it?
I'm guessing ...unzip the file, connect Profilux via RS232/USB and launch 'Flash' application?
Is this correct?
Which...
Hi Matthias,
Thanks for the swift response, I have tried several times to reset the pin using Enter+Esc keys at start up, the PIN code is shown on the Profilux screen as 0000 but entering this on...
Hi,
I have a PlusII connected to Profiluxcontrol V5152 through RS232/USB (Windows7 64bit).
On COM3, Baudrate 9600, FDTI driver.
When I click 'connect' in Profiluxcontrol I am asked for a PIN. I...