Search:

Thank you.

Thank you, now it is clear.

How many PNL60-48D can I connect to each dimming channel?

How can I connect 4 Meanwell 60-48D (dimmable) led drivers to Profilux 3.
Specifically:
1. How do I connect the dimming wires to the L ports?
2. Do I need to connect the drivers main power supply...

Do you consider this limitation as a bug?
3% seems to be rather high for moonlight, I would have expected 3% to be the brightest light in full moon.

Also, when I have changed the ranges to:
-...

Is there a way to get the illumination brightness go down to 0% with the moonlight simulation (at new moon phase when there is practically no moon)? The lowest I am able to go is 3%.

My setup:...

Thank you Carolin. That is what I have done but it was not clear from the documentation. The documentation does not mention either two jumpers, or the fact that both should be setup the same way.

I have a similar problem, the conductivity is dropping down. If I shake the sensor in the aquarium water the reading goes back to normal but dropping quickly (from 1.025 to 1.010)

The manual for the LED-1 states that to get the unit to respond on the secondary port (L2,4,6) you need to move the jumper inside the box.
However, there are two jumpers inside. Which one should be...

Thank you Matthias.
It is working OK now. I have a problem with one unit where when in moon simulation it goes off for few seconds and than comes back.

The illumination is setup to 3% at night...

I got 4xAquaray500 and I am a little confused regarding connecting and controlling them with the profilux3 via the LED-1 controller:
1. Do you use the LED-1 controller instead of the PSU provided...

Thank you Chew, I was not able to find that information anywhere.

Why do you have to limit the contoll voltage to 3-8V ?

I finally got reefstatus on Win7 64bit to connect to profilux3ex.
However, when I try to start logging or to improt data from profilux, I get an error: cannot open reefstatus.mdf.

On the other...

Thank you Matthias,
I have changed the wave control to 'no wave' with the default settings and it seems to have solved the problem. (the wave control was blank before)

Since I am only trying to controll the current pumps on/off, I don't understand what the wave has to do with it.
When I just got the profilux I have tried the wave controll but it did not work so I...

The Koralya pump are connected to the S ports. The don't have varialble speed controll so I only use the random function to turn them on/off for period of times.

I have Profilux3e
FW 5.00m
PC software 5.0.0.8
Using digital powerbar with 6 outlets.
You can see the system setup on the attached doument.
The pumps stay constantly at the staus you see on the...

I have 3 Koralya power heads 2xtype 3 1xType 4 controlled by profilux3ex
The pumps are connected to a digital powerbar.
Pumps 1&2 are in group 1 and pump 3 in group 3.

Group 1 is programmed to...

Thank you Mathias,

Also, the remote control does not work properly:
1. the display on the profilux is 3 lines and the pc side shows only 2 lines
2. when you try to operate the remote control,...

When I try to transfer all settings from Profilux3 to PC I get the error message: 'Can't find paralist_v500.para file'.

I have looked for this file manually but can't find it anywhere.
I have...

I am using the original GHL cable

I have, The update started but failed with a communication erro few seconds later.

I am using a converter with the prolific chipset. Normal operations are working well but every time I have tried to update firmware it failed halfway through and I had to use a computer with serial...

I understand and thank you for the explanation.

I guess than that my only course of action is to replace the powerheads. Which powerheads can I use with the Profilux equipment I already have? I...

Thank you Micha578.
How do you go about changing the net frequency?