Hi getuiis,
My situation has been resolved with an remote online session with Josh (GHL USA). Big thank you to Josh for his help, more so as there is a 16 hour difference in our time zones.
...
Type: Posts; User: Tone
Hi getuiis,
My situation has been resolved with an remote online session with Josh (GHL USA). Big thank you to Josh for his help, more so as there is a 16 hour difference in our time zones.
...
Thanks, Vinny ... I'll give that a go :)
PS, I also have registered a ticket ... with further information.
I have a pre-loved PL4 with the most recent firmware and GCC F/W 7.28.
I have viewed the relevant videos numerous times in attempts to set up wireless connection and myGHL.
I did establish the...
Thank you, Vinny. :)
posted at 'Miscellaneous' as well
Hello All,
I have recently purchased a secondhand PL4 from a fellow reefer and I am unable to make a connection to Control Centre Vers. 1137. I currently have...
Hello All,
I have recently purchased a secondhand PL4 from a fellow reefer and I am unable to make a connection to Control Centre Vers. 1137. I currently have a PL3e running the display.
Only...
Thank you Vinny ... all power settings now synchronised ;)
Hi,
I have 4 x 6200HV's running on my display, purchased at the time the 7200's were first released, so not so old, and set up as 1xmaster/3xslave. I had noticed at the time that one of the units...
Hi Vinny,
Thanks for your help.
I have since reset the entire P3, examining all settings for everything and found numerous instances where the settings for the reinstallation of the set-up...
Hi Vinny,
So I've corrected the setting as advised ... even switched to "special weekdays" mode and it still does not run on automatic.
It does run using the "dose now" manual mode so there is...
Hi Vinny,
Thanks, for some strange reason, the CC has previously not allowed me to change this but now it will. I will see how this goes ;-)
Hi Vinny,
Thanks for your assistance ... however this has not helped.
Additional images requested are attached.
11405
11404
Also, let me draw your attention specifically to this, what...
I have the pre-vers 2.0 4-pump dosing unit and recently upgraded Control Centre to the latest version.
Pump one on the doser has stopped working with the automatic scheduling ... manual dosing...
ALL OK -- FOUND IT
The allocated channels somehow got switched back to 'always off'
OK so I had it set up and going great in automatic mode.
After a few days it has now stopped ... power is working, comms light is on but the P3eX stopped sending signals to the doser. I tested it...
Problem !
I can get the unit to run when I use the 3m GHL RJ12 cable but when use a 10m RJ12 cable so that I can locate the dosing unit in the right location, there is no communication between the...
Cheers, Vinny! :cool:
All done! :rolleyes:
I have decided to use S5-S8 on the PAB (P3eX).
My process:
(1) Connect power to doser
(2) Enable digital power bars for S5-S8
(3) Plug the doser into the socket S5-S8
(4) Access numbering of...
Thanks, Gunter!
Thank you Gunter!
I have a P3e controller.
At the back of the doser are 2 x RJ jacks, which one is connected to the P3e?
What about the power adaptor, is there any special requirement for...
Thank you, Vinny. I have already reviewed that "manuel" [sic] and it imparts no useful information to me ... what cables are used to connect to the Profilux, which port the cable is plugged into, how...
I have recently purchased a secondhand Gen 1 Slave dosing unit. I have some questions: :confused:
(1) What items should be supplied with the unit (ie. when it was new what would GHL have supplied...
Matthias, I would love to buy 4 x Lx6200 or even 7200 but I am unable to create a delivery address for Australia from the GHL Shop. Please will you help me create the order.
Kind regards, Tony
Thank you, Matthias.
Hello, can anybody advise me whether a 6100 LX can be upgraded to HV and what the likely cost would be (Euro$ would be ok)?