I have installed the new ControlCenter 1.1.3.7 yesterday. And in Control Center, the software informed me that there is a new firmware (ver7.24) but I cannot install it as it says I do not have the...
Type: Posts; User: palmlover
I have installed the new ControlCenter 1.1.3.7 yesterday. And in Control Center, the software informed me that there is a new firmware (ver7.24) but I cannot install it as it says I do not have the...
I want to show the particiular sensor's data in the email. The present email is to show all sensor as :
Temperature 1 : 26.4C
pH-value 1 : 6.03pH
Redox 1 : 345mV
Conduct.(S) 1 : ...
I cannot find the P4 firmwareV7.24. Where can I find it? and. what is the difference from V7.23?
Thank in advance.
I have the same problem. ONce I have updated the firmware and wifi firmware, I cannot connect with MyGHL. The connect with local wifi is ok that I can connect with the P4 with wifi. (Green Light is...
In manual, Ph 7 and 9 is for aquarium while 4,7 is for fresh water. Yet, my ph probe mainly measures between ph 6 to ph 7.8(or elese but not higher than ph8).
Thus, can I calibrate the probe...
Thank All. I find that I need to check data recorded in CCG.
Wish that this can be done in Webserver/myghl in futire.
Thank so much! May I have one more silly question. When should I set Doser 2 as slave? After connecting with P4 or before I connect it with P4? (And, I connect with P4 to do so or connect with Doser...
Thank Gandalf. Where I can tell Profilux to record the data?
Thank you Benutzer. Where can I set DOSER SA as slave? In Profilux?
And, CAT 5/6 PATCH CABLE <=== Do you mean cat 5 cable for network usage? And, which port I should insert in P4? The second PAB...
Can I connect a standalone Doser 2 to Profilux? If yes, what additional equipment I need to buy and how I connect these two devices?
I have connected with MyGHL with my Profilux 4. I cannot see the chart as there is no date recorded. What should I do?
11483
Besides, I just find that there is failed to sync with MyGHL as...
If a cable (land card) can solve the problem, I will be happy. Yet, as my understanding, lan card cannot be used for P4.
I have set prog logic to delay skimmer on 60 seconds as follow :
G1 =>Name=Maintenance 1 => Function<delay on (60s)
Then I assign socket 5 (for skimmer) to prog logic 1
However, the...
Test router?
I confirm that my router is no problem as various device hwve been connected with this router. All, except P4, connect with router very well.(In fact, my Doser 2 SA also connects...
Dear Yosh01
Do you mean the wifi issue solved? I have tried to make P4 powerless for several times, the issue is still here. In GCC, there is red x at the powerbar and MyGHL (This i my most...
When I connect P4 with wifi (intranet), this is ok and reasonable. At the same time, GCC tells me that signal is poor (red x at signal bar). And, myghl cannot be connected.
Then, I do not...
Version is 1.06. I have tried upgrading the firmware to 1.08 but always failed. (POP up message box saying that tranmission of data to device failed)
Dear Matthias
I do not mean to be offensive but my experience on the firmware upgrade is somehow different from the videos and I have met some strange situation that I do not know why. Though...
Sorry for making confusion. This is just sharing because I do not see any stuff in Dashboard till this morning.
Dear Mathias
If so, please make it forbidden in GCC and should make clear statement in manual. (I do not find any warming in manual nor GCC. LUCKILY, I DO.not. have any problem.)
I have found that P4 data now shown on Dashboard!
Though official reply that transfer of P3 data does not work. I find some data is still successfully transefered.
Dear Ega
I have similar experience. I cannot find any keys can be prrssed/reseted at P4. Turn off /turn on the power also not works. Finally I just ignore this windows (press ok without doing...
Thx Marco.
How I should connect to P4? Do I need to buy any cable? and what the cable is?
Thank you Tinpot.
Follow your suggestion, I successfully upgrade the firmware.