Hi,
I have, for 6 months, successfully used the EVG-AP-2f-HIC on my Profilux 3.1N (6.11). It is hooked up to a Meanwell ELN-60-48D powering 13 or 15 (tried both amounts) Cree LEDs.
Now it is...
Type: Posts; User: funkyaneurysm
Hi,
I have, for 6 months, successfully used the EVG-AP-2f-HIC on my Profilux 3.1N (6.11). It is hooked up to a Meanwell ELN-60-48D powering 13 or 15 (tried both amounts) Cree LEDs.
Now it is...
The perfect solution would be to activate AWC through programmable logic when the level sensor for a full reservoir is triggered. Unfortunately, as far as I can tell, programmable logic isn't that...
Ok, I've figured out how to run the AWC (socket 1&3 with sensor 1&2) on a timer, with the pre-fill of the reservoir run by ATO (socket 2 with sensor 3) triggered by a timer a few minutes before the...
Hi,
I’m sure you more experienced Profilux users could achieve this. I, however, am a completely confused noob. I hope you can help me, please!
How do I set up AWC with an automatically...
Hi gnisten,
Did you find a solution for this? I'm trying to do the same thing.
Thanks.
Andrew
Ironically, now that the probe is back in the aquarium it's back to showing 10.50. It has been stuck on 10.50 for the past few hours. That's how this started. That's how I found Brian's thread to...
Hi Gunther.
I just ran another calibration with the following results;
ADC1: 716
ADC2: 714
The reading in the 9ph solution is now swinging between 9.03 and 8.91 (changes once a second to a value...
Hi Gunther. Thanks for your reply.
The probe is brand new. I've had it for only a few weeks and it has been in the tank only a few days. Could there be another explanation?
Thanks,
Andrew
Hi Carolin,
I'll test the readings in the calibration fluid when I get home from work.
The probe's readings of the aquarium water, over the past few days have steadily reduced from 10.5 down to...
Hi Brians,
Did your ph probe issue work out?
I'm having an identical issue with a brand new probe.
With mine, after a day in the tank, the ph reading has now dropped to 8.9. Wait, it's now...
Solved.
I had to uncheck "search automatically" to be able to enter the correct external I.P.
Andrew
The possible cause at the top of my list is the connector on the EVG which receives the 6 wires from the Profilux control line.
When installing the wires in this connector, I believe the connector...
Hello,
My LED unit is not working as required via the EVG-AP-2f-HIC.
I have just installed the EVG-AP-2f-HIC on my Profilux 3.1N (6.11). It is hooked up to a Meanwell ELN-60-48D powering 13 or...
Hi,
I currently use ProfiluxControl 6.0.6.0 on my laptop computer to access my Profilux 3.1N (firmware 6.11). This works when my computer and the Profilux are on the same network.
However, is...
Hi,
Quick question; Is the built-in conductivity port for the 3.1 N EX suitable for freshwater? I ask because I know GHL sell separate expansion cards/probes for freshwater and saltwater.
...
Hi,
Can one single level sensor be used to trigger one event (when the water level reaches the trigger height) and ALSO trigger another separate event (when the water level drops below the trigger...
Hi Matthias,
Thank you for your response.
Is this the manual to which you refer? http://support.aquariumcomputer.com/downloads/ProfiLux31all_Manual.pdf
I cannot find a "level sensors"...
Hi,
Is it possible to program one water change sequence (using pumps, sensors, doser, etc) then also program another, different, water change sequence using different combinations of sensors,...