Search:

I’ve since upgraded the firmware to version 6.46 and still have this issue, both a blank screen after startup and the missing DALI addin card. In GCC System view I can see two serial cards listed...

Hello, I updated my P3 eX from firmware 6.36 to 6.43 yesterday and my settings remained however I seem to have a blank screen on the device after the initial startup logo appears and also the DALI...

Hi Vinny, I think there may be a slight misunderstanding of what I'm asking. Just for clarity and leaving out anything connected to the PIII such as Plugbars etc, I'm aware that one option to keep...

Ok, I'm revisiting this as I still have a PIII...so, the Tunze Safety connector basically has two inputs, one from the Tunze Pump PSU DC and the other from the 12V Battery, the output is a single DC...

HI Vinny, that's interesting, can you provide any more information about the power monitoring port please?

Hi Vinny, but if the PSU fails (like mine did) the UPS won't help...Is there battery backup for the P4?

Just me looking to do this then?

Hi, I currently use a 12V Sealed Lead Acid battery and Tunze safety connector to provide a battery backup for my Tunze pumps...after having my PIII PSU fail whilst on holiday, I wondered if there is...

Hi Matthias,

Thank you for your prompt response. I saved both sensor data and settings (as I always do) prior to the firmware upgrade, although I generally only reapply the setting and tend to...

Can I ask if I am following the correct procedure for requesting support from GHL? I have posted an open request for assistance 1 week ago with no response, I have asked politely for anyone to...

I didn't take a note of what the original ADC values were for the expansion box but I would have thought they would be unique to the box and not the same as the Profilux main unit? Can anyone from...

Any feedback please?

Hi, I have a P3eX with and V1 expansion box, both with temp probes connected. Until the latest firmware update to v6.27 the two probes tracked each other within 0.1 - for example when Temp1 read...

Hi, I have a four head original doser connected to my Profilux 3 for dosing Balling Light alk, I'm considering buying a two head Doser 2 slave to dose Fauna Marin Colours, are the heads from the...

Hi, when I connect to my Profilux 3 eX using the latest V1073 software and try to update the firmware from 6.14 to the included 6.18 I get a popup box saying "This file is unsuitable for updating...

Hi Janey, I have the same setup with the Tunze pump, you need to connect the Tunze pump to a 12V DC adapter and plug the adapter into a free socket on your GHL Powerbar. The two sensors can both be...

No response from GHL, wow, it's not like this is important at all....

Hi, I have two PAB powerbars and a 4 channel doser, PAB bar 1 is S1-S6, the doser is S7-S10 and the second PAB bar is S11-S16; this has been setup this way for a long time however after a brief power...

Thankyou Carolin, as I understand it, the "Heater" is only switched on if the "Bottom Heater" is not sufficient, so should I assign Socket 1 to "Temperature 1" & "Substrate Heater" and Socket 2 to...

Hi, I have two Shego titanium heaters (no built in thermostat) - can anyone tell me the best way to set these up to maintain 26C? I have read a post regarding using one set as "Heater" and the other...

I have two 6095's controlled via the GHL and they do not perform the "fish care" move when paused. I asked on ReefCentral and Roget Vitko confirmed that the function had changed recently so I tested...

I have now, thankyou :)

Hi, would it be possible to enhance the current Tunze modes to match the storm mode that the Tunze 7096 controller can do: -

"Storm cycle" - storm for desedimentation
As in nature and similar to...

Hi Matthias, as you know when Profilux power fails any Tunze pumps controlled via Profilux also stop despite being connected to battery backup. There was a DIY suggestion in the German forum that...

Hi Matthias, seriously, is this something you could manufacture - a new Tunze cable that allows battery backup to work or an addon to existing cables maybe? I'd really like to see the Tunze...