Suchen:

Art: Beiträge; Benutzer: Vinny

Seite 1 von 20 1 2 3 4

Suchen: Die Suche dauerte 0,02 Sekunden.

  1. Thema: skimmer control

    von Vinny
    Antworten
    4
    Hits
    136

    As mentioned above, you will need to use...

    As mentioned above, you will need to use Programmable Logic if you want to have the skimmer react to all 4 Feed Pauses. Go to the PL settings page, choose an unused gate, set the function to AND,...
  2. Antworten
    2
    Hits
    106

    That seems to be an older version float sensor....

    That seems to be an older version float sensor. Test it out first to make sure it's reacting when you manually move the float up and down.

    Yes, you can cut the cable and re-wire it if you are...
  3. Thema: Probe placement?

    von Vinny
    Antworten
    1
    Hits
    98

    Hi, Ideally the probes should be placed in an...

    Hi,

    Ideally the probes should be placed in an area where there are no microbubbles present. If that is not really option, an area with minimal microbubbles is the next best thing. You don't want...
  4. Thema: Wifi update

    von Vinny
    Antworten
    3
    Hits
    123

    Hi there, While you wait for a reply in your...

    Hi there,

    While you wait for a reply in your ticket, take a look at this article:
    https://www.aquariumcomputer.com/knowledge-base/how-to-update-or-restore-wi-fi-module-firmware/

    Since you are...
  5. Antworten
    2
    Hits
    150

    Hello, If you haven't done so already, please...

    Hello,

    If you haven't done so already, please email us directly:
    sales@ghl-kl.de
  6. Thema: Alarm PABCOM

    von Vinny
    Antworten
    1
    Hits
    110

    Hello, Please open a support ticket for...

    Hello,

    Please open a support ticket for assistance with this.
    If you have an existing ticket for the repair case, you can reply to that to re-open the case.
  7. Yes that is correct.

    Yes that is correct.
  8. Antworten
    8
    Hits
    194

    Hi Aaron, If you do decide to grab that PB-6D...

    Hi Aaron,

    If you do decide to grab that PB-6D (non-PAB), you will have to first re-number your existing powerbar outlet so they start at 7. This new PB will be assigned as 1-6 and the original PB...
  9. Thema: Co2 logic

    von Vinny
    Antworten
    1
    Hits
    158

    Hi there, Go to the PL settings page, choose...

    Hi there,

    Go to the PL settings page, choose an unused gate and set the function to AND. Select the illumination channel and pH control downward option. Assign this PL function to the outlet of...
  10. Antworten
    4
    Hits
    531

    The Y-piece can be used to connect your WC waste...

    The Y-piece can be used to connect your WC waste water and KHD waste water. The vent tube should be kept separate.
  11. One RS232 device can be connected to the port at...

    One RS232 device can be connected to the port at a time.
  12. Antworten
    4
    Hits
    531

    Hello Eli, As long as the waste water tube is...

    Hello Eli,

    As long as the waste water tube is pointing downwards and runs no risk of sending water up the KHD waste tube during a WC, that would be fine. A Y-piece would probably be a better...
  13. As long as the cable is designed for use with a...

    As long as the cable is designed for use with a GHL controller, yes. Otherwise, it would be best to use a BO box.
  14. Antworten
    1
    Hits
    233

    If no network is found, you have the option to...

    If no network is found, you have the option to manually type-in your network name and password.
    Instructions for getting the doser connected to your Wi-Fi can be found here:...
  15. Antworten
    6
    Hits
    433

    Yes it's possible. Use a PL-LY splitter cable.

    Yes it's possible.
    Use a PL-LY splitter cable.
  16. Antworten
    10
    Hits
    586

    Ruben, Your screenshot shows you using GHL...

    Ruben,

    Your screenshot shows you using GHL Control Center which is the incorrect software. It will not work this way because this software does not support the PII.

    You should be using ProfiLux...
  17. It should work fine. Since each 1-10V port on...

    It should work fine.
    Since each 1-10V port on the ProfiLux supports 2 independent illumination channels, you can set 1-10V ch.1 to Illumination #1 and 1-10V ch.2 to Illumination #2.

    More info on...
  18. Antworten
    2
    Hits
    353

    As Gael mentioned, those are not genuine GHL...

    As Gael mentioned, those are not genuine GHL probes. They also do not seem to have any markings to indicate what they are. It would be best to purchase new probes.
  19. Antworten
    7
    Hits
    479

    Did you read the "How to connect over USB"...

    Did you read the "How to connect over USB" article?
    There it provides you with tips and photos of what your device manager window should show. There is also a video showing how to manually install...
  20. Antworten
    7
    Hits
    479

    Hello, Unfortunately, it is not clear which...

    Hello,

    Unfortunately, it is not clear which platform you are wanting to use (GHL Control Center or GHL Connect) to make changes to your P4's network settings. We do have an article in the...
  21. Antworten
    6
    Hits
    571

    Easy. :) Create a new PL function where you...

    Easy. :)

    Create a new PL function where you select your current PL as Input 1 and the maintenance mode (Inverted) as Input 2.
  22. Antworten
    1
    Hits
    425

    Push notifications will be made available in a...

    Push notifications will be made available in a future update.
  23. Thema: Profilux II

    von Vinny
    Antworten
    2
    Hits
    500

    Please open a support ticket.

    Please open a support ticket.
  24. Antworten
    2
    Hits
    222

    Check your chart settings and make sure you have...

    Check your chart settings and make sure you have selected the probes you want to see data for.
  25. Hello Kasper, It would be best to contact...

    Hello Kasper,

    It would be best to contact GIESEMANN for clarification on their "control" wire. The wires coming from the "1-10V" cable should be connected to the BO box. If you can post a photo of...
Zeige Ergebnis 1 bis 25 von 500
Seite 1 von 20 1 2 3 4