Search:

Type: Posts; User: itsmorefun

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    13

    Hi For 2 flow sensor and 2 level sensor with 2...

    Hi

    For 2 flow sensor and 2 level sensor with 2 Y on P4 -> yes.
    For flow sensor on mini this need to be clarified, adapter no yet available.

    PS: See also:...
  2. Replies
    3
    Views
    80

    Hi, Try do get news from this user:...

    Hi,

    Try do get news from this user:
    https://forum.aquariumcomputer.com/showthread.php?10759-Wireless-PAB-Extension&p=97948

    Gaël
  3. Hi, Sorry, I already told you what can be done....

    Hi,
    Sorry, I already told you what can be done.
    Forget programmable logics, they can't do that and can only be applied to switchable channels.

    Gaël
  4. Replies
    2
    Views
    33

    Hi, ...

    Hi,

    https://www.aquariumcomputer.com/knowledge-base/how-to-add-a-virtual-probe/

    Gaël
  5. Hi, Set U Min to 0 et U Max to 5 Increase...

    Hi,

    Set U Min to 0 et U Max to 5
    Increase Hysteresis for higher range.

    For exemple, with U Min set to 0v et U Max set to 5v and pH hysteresis set to 1pH:
    with nominal value = 8.0 and current...
  6. Relay 1: max. 100mA (open collector: active =...

    Relay 1: max. 100mA (open collector: active = GND, inactive = floating)
    GND = Ground = 0V, outputs with clamp diode to GND.

    Gaël
  7. it is indeed logical not to send a negative...

    it is indeed logical not to send a negative voltage in 0-10 volts I think it is implemented in the same way as for the temperature, when it is negative the relay is activated. see if the relay...
  8. Yes in both directions The range seem defined by...

    Yes in both directions
    The range seem defined by hysteresis.

    with nominal value = 8.0 and hysteresis = 0.1 and current ph = 8.1 you will get 5v
    with nominal value = 8.0 and hysteresis = 0.1 and...
  9. Hi, Yes, "The selected controller outputs then...

    Hi,

    Yes, "The selected controller outputs then a voltage that is proportional to the control deviation (= deviation from nominal value to actual value) at this interface."

    Gaël
  10. Replies
    6
    Views
    179

    Did you connect an ethernet network cable between...

    Did you connect an ethernet network cable between your internet box and the LAN socket of the Profilux?

    Gaël
  11. Hallo, Ihr Profilux mini Wifi benötigt...

    Hallo,

    Ihr Profilux mini Wifi benötigt mindestens die Firmware 1.13 für Historie, die bald mit dem nächsten GHL Control Center verfügbar ist

    Gaël
  12. Replies
    6
    Views
    179

    Can you use LAN instead of this WLAN card? I...

    Can you use LAN instead of this WLAN card?

    I do not recommend this WLAN card and strongly advise you to connect with LAN but if you really want it, try to see what you can do with this manual but...
  13. Replies
    6
    Views
    179

    Hello, 192.168.0.0 is invalid IP On P3 LCD...

    Hello,

    192.168.0.0 is invalid IP

    On P3 LCD panel go to System -> Communication -> LAN and set/read current ip settings.
    Use this IP in GHLConnect.

    Gaël
  14. Thread: P4 firmware

    by itsmorefun
    Replies
    2
    Views
    198

    Hello, 7.28 available with...

    Hello,

    7.28 available with https://www.aquariumcomputer.com/downloads/ghl-control-center-v1-1-3-7/

    Gaël
  15. Replies
    3
    Views
    213

    Hi, As the document quoted by Gandalf...

    Hi,

    As the document quoted by Gandalf indicates, the 1-10v outputs should only be used to transmit a control signal and NEVER to supply a power device such as a motor. The output must not be...
  16. Replies
    2
    Views
    446

    Hallo 13246 oder 13247 Gaël

    Hallo

    13246
    oder
    13247

    Gaël
  17. Replies
    7
    Views
    964

    Yes. Gaël

    Yes.

    Gaël
  18. Replies
    8
    Views
    470

    Hi, Is it new or second hand doser? Can the...

    Hi,

    Is it new or second hand doser?
    Can the heads of your dosing pumps be worn out? This is because it is possible that the precision of the dosages are affected and therefore the precision of...
  19. Replies
    7
    Views
    964

    Hi, Profilux mini can't control LX6 or LX7...

    Hi,

    Profilux mini can't control LX6 or LX7 because you can't add a expansion card as PLM-PWC on Profilux mini.

    Gaël
  20. Hi, Yes ...

    Hi,

    Yes

    https://www.aquariumcomputer.com/knowledge-base/how-to-setup-vortech-pump-control/

    Gaël
  21. Hi, No, you have to backup settings and...

    Hi,

    No, you have to backup settings and sensors data before the update and restore theses 2 files after.

    Gaël
  22. Hi, GHLConnect use the locale of the system...

    Hi,

    GHLConnect use the locale of the system for formatting numbers, date and time
    Maybe it's only a bad region/language which was set on your iPhone.
    Otherwise open a support ticket as @Vinny...
  23. Replies
    3
    Views
    577

    Das ist der Punkt

    Das ist der Punkt
  24. Replies
    3
    Views
    577

    Hallo, Versorgen Sie ein Relais mit einer...

    Hallo,

    Versorgen Sie ein Relais mit einer Stromversorgung, die an die zu überwachende Steckdose angeschlossen ist.
    Wenn dieses Relais erregt ist, stellt es einen Kontakt zwischen Digitaleingang 1...
  25. Replies
    7
    Views
    719

    Hi, So this is not the origin of the problem...

    Hi,

    So this is not the origin of the problem but it could have been if this parameter has been checked and the Profilux had restarted because of the power cut.

    Gaël
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4