Hello All,
First off, I tried to download the Profilux Touch manual and this is what I see:11244
Here is what my GCC shows when I connect to the Profilux3.1ex N (up to date FW) and click on...
Type: Posts; User: scythanith
Hello All,
First off, I tried to download the Profilux Touch manual and this is what I see:11244
Here is what my GCC shows when I connect to the Profilux3.1ex N (up to date FW) and click on...
Thanks for the help AdrianF. I tried hitting the sync mode and that wasn't doing it so I figured I should take another look on the GCC. So I got into the pump assignments and low and behold there was...
Can anyone from GHL comment on this? I have read through the VorTech Controller Manual and I cannot see any mention of assigning a master or slave pump in GCC. Or am I supposed to set groups directly...
Ok it took a while but I have assigned the STDL4-4 to S1-S4 non-digital (also plugged into S1-S4). Reassigned the slave Doser to S5-S8 digital and gave it S26-S29. Renumbered all the Powerbars from...
The three powerbar6D's I have are PAB devices. How would I go about connecting it to the S5-S8 port? Or do you mean run a PAB cable from the P3 PAB port to each individual PB6D one at a time?
I always do. I reloaded my settings once the FW flash was complete but the PAB devices weren't there anymore. All good now though.
Like the title says, can I plug my P3 into the Doser 2 LAN port and have it share its wifi internet with the P3?
Thanks!
Hello,
I am trying to add a STDL4-4 powerbar to my setup. I currently have my Doser plugged into S1-S4, and assigned as S13, 14, & 15. So I have to plug in to S5-S8. When I power up the powerbar...
Ecotech confirmed they are all in anti-sync mode. Can I set which should be sync and which are anti-sync through the GCC?
Hello All,
I have my VorTech Controller module up and running again. All the indicator lights on the VorTech control dial have settled on what seems to be a single colour, almost a peachy orange....
They used to be on there. Why would they be taken off, firmware update?
Done, they have been assigned and I now can see the VorTech overview :) Why would it keep working away but not be assigned?
I have updated to GCC V1118 and It looks the same. All I see in my PAB chain is serial, humi & temp, & PWC. I went into assign devices and I see my 3 powerbar 6's, Profilux touch and Vortech...
Hello,
I have been using the VorTech Controller on my P3 for years and recently decided I wanted to go and change the settings a bit. But damned if I can find the "Vortech Overview" tab in GCC?!...
That did it! Thanks.
I upgraded to GCC 1.0.9.0 and got the same error essentially. This time it has _V1099 instead of _V1090.
Can anyone point me in the right direction here? I'm trying to update the mitras firmware through GCC 1.0.9.0 and I get this error:
...
Can you refill the solution through the app?
After all of that I re-connect and the USB connection works fine. I can go in and edit the dosing program without issue.
6843
Done and done. I have Com4 for my GHL stuff. Still doesn't work.
6838
6839
6840
6841
Hello,
I updated to the new GCC and connected to my Doser 2 to update to FW version 1.02. For some reason the FW was interrupted and I got an error message. It said to unplug the Doser 2 for a...
It would be in Apples hands now if GHL had submitted it to the App department.
I can shut this one down lol :)
Michael, I don't mean to attack you or GHL. I feel, due to the limitations of the internet and it's inability to convey tone, that when you add you "fun" aspect to...
I can talk about anything I want in this thread, I started it ;) I was referring to GHL products as a whole in my previous post.
GHL has its pluses without a doubt, but it also has its negatives....
That's great that it's being worked on.
I don't know what you think GHL has that some other companies don't? I'm sure this won't go over well on a GHL forum but it's the honest truth. Neptune...
Hi GHL,
I am just curious as to when you think the Doser 2 apple device app will be released?
Thanks,
Scott