Search:

Type: Posts; User: Oldtimer

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    3,902

    Nevermind - since I have a replacement controller...

    Nevermind - since I have a replacement controller now I realized that I didn't yet reprogram the digital sockets. I just did that and the powerbar is functioning normally. To be honest, it might not...
  2. Replies
    7
    Views
    3,902

    Hello, I have to revive this thread as I have a...

    Hello,
    I have to revive this thread as I have a similar issue with my 6D powerbar connected to Profilux Plus II EX. It was very close but likely the bottom portion got wet during a recent flood of...
  3. Replies
    7
    Views
    2,657

    Separate question: My dosing unit (4 head...

    Separate question: My dosing unit (4 head version) was also submerged in water. I performed the same cleaning procedure. I since powered it and it displays a green light indicating it has power but...
  4. Replies
    7
    Views
    2,657

    I have a feeling there must be a hardware issue...

    I have a feeling there must be a hardware issue with the EX module so to avoid further delays, I just found where to order from aquariumcomputer.com and placed an order for a new EX module. My plan...
  5. Replies
    7
    Views
    2,657

    OK, so I performed the following: 1.)...

    OK, so I performed the following:

    1.) Installed Firmware 5.17
    2.) Successfully connected controller to Profilux PC software V5.7.1.2
    3.) Found drop down menu option to upgrade software to...
  6. Replies
    7
    Views
    2,657

    Perfect. Thank you!

    Perfect. Thank you!
  7. Replies
    7
    Views
    2,657

    Thank you - but wouldn't it be better to update...

    Thank you - but wouldn't it be better to update the FW of the new controller? The old controller had some corrosion on it. I did not attempt to clean it with alcohol - only the EX board which I then...
  8. Replies
    7
    Views
    2,657

    Profilux Plus II Ex

    Hello,
    After an unfortunate event last weekend = 1 meter of water in our finished basement, my Profilux Plus II Ex controller was submerged in water for some time. Since it was powered via a GFCI...
  9. Right, but that requires you to have a PC...

    Right, but that requires you to have a PC connected with Profilux Control software loaded, which I did not at the time so I lost it all. I've since saved all settings and upgraded to firmware 4.08....
  10. Also, it's worth nothing that I upgraded the...

    Also, it's worth nothing that I upgraded the firmware of the controller and the level of Profilux Control to v4.08 a few days ago.
  11. OK. I just spent over 2 hours on the phone with a...

    OK. I just spent over 2 hours on the phone with a tech from Linksys (maker of my router). They were able to restore my wireless connection. And we eventually were able to get connected to the WLAN in...
  12. Thanks Matthias. I will try it again today after...

    Thanks Matthias. I will try it again today after work, but I first have to call Linksys and figure out why my wireless connection is hardly working now. Actually, I tried to reset the router again...
  13. I found this link......

    I found this link... http://www.youtube.com/watch?v=BAqi-tszty8 and it was very helpful although I could not connect at the end. If it matters, my security is WPA2 Personal and picked WPA2 when I...
  14. Figured out how to resolve this. After I udpated...

    Figured out how to resolve this. After I udpated the factory settings and typed the above message, I closed the program and walked away. I just had an idea to check some settings and when re-opening...
  15. Need Help FAST - Firmware update Plus II EX, v3.08 to 4.08

    I just downloaded v4.08 and it was successful, although the controller did not appear to reboot but instead flashed a message in German "einstellungen rueckgesetzt!!!" Translator says it means...
  16. Perhaps the link is not what you intended because...

    Perhaps the link is not what you intended because I see multiple movies on the link, but nothing that looks related. Appreciate the help.
  17. Need Help Connecting Via WLAN Profilux EX Plus II, fw v3.08

    Firstly, I will note that my reef setup is in the basement and my wireless router is 2 floors above. I get a strong wireless signal in the basement, but I just wanted to note this before you read...
  18. I'm afraid to try and power cycle now because I...

    I'm afraid to try and power cycle now because I don't want to spend 2-3 hours programming all settings again. I don't have much time to spare these days. I understand I can save settings once I have...
  19. Very unhappy - Lost all set points during power outage, why??

    Profilux Plus II EX - I lost all programmed data when my power shut off this morning. When the power was restored, the controller flashed something like "restoring factory default values" and then...
  20. I did this last night and it's working fine now...

    I did this last night and it's working fine now with conductivity control.
  21. Another option I'm considering is using my...

    Another option I'm considering is using my conductivity probe to switch on the dosing pump once conductivity rises above a certain level. Then I can use the optical sensor as a protection for the...
  22. OK, I will try to reset it and see what happens.

    OK, I will try to reset it and see what happens.
  23. By screenshot, I'm sure you mean to take a...

    By screenshot, I'm sure you mean to take a picture of my PC, but I'm only using the controller to program, not my PC. If this is critical, I will have to setup my WLAN... I just haven't found the...
  24. Problem setting up Profilux Optical Level Sensor

    I have an optical sensor on the Level 1 port in my Profilux II Plus EX. I cannot get it to switch on my ATO pump. The ATO pump is actually channel 1 on my Profilux Dosing Pump. Channel 1 is on socket...
  25. Thanks Matthias. I found the 0-10V setting in the...

    Thanks Matthias. I found the 0-10V setting in the controller and changed from 1V to 2V and it worked perfectly!
Results 1 to 25 of 34
Page 1 of 2 1 2