Search:

Type: Posts; User: marios

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,886

    So I will need to upgrade to at least Profilux...

    So I will need to upgrade to at least Profilux III or there are still available old style dosing pumps?
  2. Replies
    3
    Views
    1,886

    Doser 2 Slave backward compatibility

    Is th enew doser 2 slave compatible with the Profilux II ex ?
  3. Replies
    0
    Views
    7,531

    Manual water change

    Hi All,

    I would like to use my profilux IIex plus to assist me in a manual water change in my planted fresh water tank. I have one level sensor which I use for ATO however I am draining the tank...
  4. Replies
    7
    Views
    3,902

    Dear Carolin, Thank you for your response,...

    Dear Carolin,

    Thank you for your response, taking the computer out of operation poses great threat in my system as beeing in Cyprus would mean that at least one month would be required for this...
  5. Replies
    7
    Views
    3,902

    I have a ProfiLux Plus IIeX and the 6D is...

    I have a ProfiLux Plus IIeX and the 6D is connected on S1-S4. This system has been configured like this and working flawlessly for 4 years so it is not a new config that does not work. The 6D...
  6. Replies
    7
    Views
    3,902

    6D powerbar stopped working

    Hi Forum!

    I have a profilux IIex that have been using for almost 5 years now. I have on it a 4d analog bar and a 6D digital powerbar. Recently my 6D bar stopped working and the only LED that is on...
  7. Replies
    2
    Views
    2,593

    Hi Mathias, What if I want to perform this...

    Hi Mathias,

    What if I want to perform this manually. Meaning turning off the skimmer for 2 hours by pressing a button. I guess maintenance or feeding pause?
  8. Replies
    5
    Views
    3,126

    I still have problems with this cable. Do you...

    I still have problems with this cable. Do you have a product code for a replacement cable?
  9. Replies
    5
    Views
    3,126

    Problem Fixed! I used a multimeter and checked...

    Problem Fixed!

    I used a multimeter and checked one of the pins that was looking a bit rusty. This showed no continuity between the two cable sides so I replaced the RJ12 on that side with a new...
  10. Replies
    5
    Views
    3,126

    Yes I have tried all of the above. I cannot...

    Yes I have tried all of the above. I cannot connect digital to S5S8 as this is a Profilux IIex. As I said I tested the cable with the digital PB as well which works ok otherwise with my other cable....
  11. Replies
    5
    Views
    3,126

    power bar control cable broken?

    Yesterday I started my new tank. I have two powerbars, one 6D and one analogue. I have the digital connected to S1-S4 and programmed as plugs S9-S14 and the analogue is connected to S5-S8 port....
  12. Replies
    3
    Views
    3,577

    Mathias, thanks for the answer however I do not...

    Mathias, thanks for the answer however I do not see the logic.

    If I put AND I would need to activate feeding pause and maintenance at the same time so that the skimmer switches off. This does not...
  13. Replies
    3
    Views
    3,577

    Adding delay to skimmer start

    I know this have been discussed in the past however I cannot find anywhere a combination of both situations.

    I have profilux II ex with 4.6 firmware

    What I want is the skimmer pump to be...
  14. Thread: Chiller Control

    by marios
    Replies
    4
    Views
    4,470

    Chiller Control

    Could turning on and off of the Chiller by the computer cause any problem at the chiller itself? I am using a TECO TR20 with the temp setting calibrated to match the temp reading from GHL and the...
Results 1 to 14 of 14