Search:

Type: Posts; User: onlyco

Search: Search took 0.01 seconds.

  1. Thanks.

    Thanks.
  2. By the way, If I upgrade my P3 to P4, Do I need...

    By the way, If I upgrade my P3 to P4, Do I need the PLM-PWC card too?
  3. Thank you very much, I'll try it. There was less...

    Thank you very much, I'll try it. There was less information about the card on the official website, If I put the card in my P3, Will there be an setup menu add on GCC automatically?
  4. Can the Mitras LX7 be beconnected with P3.1 or P4?

    I just bought a Mitras LX7. Can it be connected with my P3.1 ? I hope the light could be linked with pumps so I can control it when I do a water change or other maintenance. My p3.1 has login my home...
  5. Copy that, thanks for reply

    Copy that, thanks for reply
  6. Flow sensor connect to expansion box 2 problem

    Dose the expansion box 2 support flow sensor? When I connected the sensor to the expansion box 2,It doesn't seem to be able to read in GCC.
  7. Replies
    26
    Views
    18,503

    I have the same issue for a year with my P3 set....

    I have the same issue for a year with my P3 set. When I take the probe out of water for a seconds and put it back, the value will be correct. After one or two days, the value will drifting down...
  8. Replies
    2
    Views
    1,997

    I met the same problem. you can try to do this:...

    I met the same problem. you can try to do this: change the probe from sea water to fresh water at GCC Conductance probe settings,the GCC wil restart selfly,then,change the probe from fresh water to...
  9. Replies
    2
    Views
    10,552

    It's very helpful, Thanks!

    It's very helpful, Thanks!
  10. Replies
    2
    Views
    10,552

    About GHL PropellerControl

    Hello, I‘m going to by a PropellerControl, there have two questions,
    1. Is the PropellerControl contain a 1-10v cable? If I need to buy the cable,which one should be choose.
    2. Can I control the...
  11. Replies
    6
    Views
    5,388

    It's a good idear, I have bought a switchable...

    It's a good idear, I have bought a switchable plugbar to cooperated with the scoket. Thanks!
  12. Replies
    6
    Views
    7,901

    I changed the socket to Switchable and click...

    I changed the socket to Switchable and click "ok",I think it was saved,I have connected the T5 lamps before, when the socket can't be turn off,nothing connected at those two socket any more. DId the...
  13. Replies
    6
    Views
    5,388

    Ok, I got it, thanks again

    Ok, I got it, thanks again
  14. Replies
    6
    Views
    7,901

    I met the same problem, I have two powerbar 5.1...

    I met the same problem, I have two powerbar 5.1 and all the socket 5 can't be turn off, the corresponding LED is off and the S5 still has power,I have changed the S5 to swithable already.what should...
  15. Replies
    6
    Views
    5,388

    Thanks for reply,I have set the minimum voltage...

    Thanks for reply,I have set the minimum voltage but it dosn't work still. I need to buy a LF-ABOX or change the ballasts. Thank u very much!8876
  16. Replies
    6
    Views
    5,388

    Giesemann SPECTRA T5 dimm problem

    Hello,
    I had bought a second-hand Giesemann SPECTRA lamp with T5 dimm ballast, the T5 was connected to my P3 via a 1-10v cable. I had set the correct L-port and Illumination channe,the T5 can be...
  17. I met the same trouble with you, and it seemed...

    I met the same trouble with you, and it seemed have been solved already. You can try to do this: GCC--"system"--"PAB"--"expansion box 2"--"configuration",change the conductivity sensor from...
  18. Circling pump settings problem(ABYZZ and Messner MP)

    Hello:

    I have just bought a ABYZZ 200 for circling and make stream(Main Pump), the pump was controlled via 0-10v interface to P3.1Tex. I set the pump in stream group at Radom mode from 50% to...
  19. Replies
    2
    Views
    2,458

    Thank you for your advice :o

    Thank you for your advice :o
  20. Replies
    2
    Views
    2,458

    Profilux 4 connects to Profilux 3.1T

    Hi:
    I have a Profilux 3.1T Ultimate-Set already.For control more capabilities,I had intended to buy a Expansion box 2.
    Now,the new Profilux 4 is coming, My question is if i can connect...
  21. Replies
    5
    Views
    3,266

    I'v got it,thanks

    I'v got it,thanks
  22. Replies
    5
    Views
    3,266

    Thanks

    Thanks
  23. Replies
    5
    Views
    3,266

    Dosing2 slave APP problem

    I have a dosing 2 slave connected with ProfiLux 3.1T eX.
    The question is if i can control it by the GHL Contorl APP,and how to set it,thanks.
Results 1 to 23 of 24