Hi all,
I would like to connect 4 light bars (main tank) and 1 light bar (second display) on my profilux.
Do you confirm i need the following ?
2 X power supplies (one per 4 lights)
1 X...
Type: Posts; User: Geoffroy Docq
Hi all,
I would like to connect 4 light bars (main tank) and 1 light bar (second display) on my profilux.
Do you confirm i need the following ?
2 X power supplies (one per 4 lights)
1 X...
Hi all,
What is the ideal distance between the Mitras lightbar and the water ?
What if the distance is greater than 10 , let say 15 cm or 20 cm ? What is the impact ?
Thank u
Hi,
I add a similar problem in the past with a USB Cable, did you try another cable?
Even if you think your cable is working ....
hope this help
Hi all,
Do you have photos of your tank illuminated by mitras lightbar ?
Thanks
Hi all,
I would like to know if the PH and temp probe must be replaced after a while.
I have them since 2011, i calibrate the PH probe every 6 months.
Thanks
Thank u for your input.
Regarding the mix, I was wondering if the lumen quota is important as the blue ocean offers more lumen than the deep actinic version.
if someone here on the forum can post...
Hi all,
I am planning to upgrade my tank lightning (110cmX70cm with a height of 50 cm - Water level set at 47cm)
As i am already an owner of the profilux 3, my first choice will go for a ghl...
Dears,
If possible, it should be possible to reset error for the level sensors.
I had an issue during my holidays, before leaving, i changed the place of the pump and the length of the pipe for...
Cool ... :-(
Unfortunately, i have a recent laptop without RS232 connector.
Do you confirm i can use a USB/RS232 adaptator without causing additional issues....
thx in advance
Dears,
I got this error when i try to update with the firmware 5.15.
profilux 3 firmware 5.12 : Error while transmitting firmware!: FLASHERASE - No response - 8
I was using Profilux Control...
Dears,
I have exactly the same "No Response from the device".
If i type a wrong password, i received well an error of type "wrong password" ....
meaning that the profilux device is well touched by...
Dears,
I thank u GHL to propose us a smartphone app controller.
I am also a mac user and i faced also the problem to run the software only available on windows.
I ran for several weeks a...
Hi, i have exactly the same problem.
Profilux is disconnected from the network after few days ....
Even if profilux is using a fixed address and router don't restart.
I created a post several...
Dears all,
I would like to know if some of you can share their settings related to pump controls and especially the Tunze pumps.
Please don't forget to provide also the dimension of the...
Thank u for your answer.
I was hoping that some profilux users can share their experience on cooling with the propellerbreeze.
thx
Dears,
I have a tank with the following dimension : 100 * 60 * 50(h) cm
the tank is rimless without canopy
with a total net volume (sump included) of 300 liters.
The tank is illuminated by 8 X...
No one experimented this problem ?
Dears,
This is second time that i see the profilux is no more connected to the lan.
The first time, the profilux came back available on the network after several days and i don't know the reason....
Thank u for your feedback Wirus.
If i understand well, i bought this card for nothing! I am really disappointed!
1738Dears,
I just have bought the WLAN card.
My plan was to replace my LAN connection (on-board) by a wireless, as my lan is passing trough a Power Line and require additional cables and power.
...
Perfect!
Your solution works well, but i was obliged to assign "always on" to the socket , save, then assign again "Prog logic 3" and save again.
I think that because the socket was already...
Thank u, it's working with latest version.
thank u it works like expected.
if i use the AND then the socket goes off immediately (without invoking maintenance or feed pause).
If i use OR, then the socket goes off when i invoke maintenance but it doesn't go off when i...
Dears,
I try to change existing logics but i get an error when i click on the "change" button when i am using PLC 5.0.9 (firmwire is 5.9 to)
1681168216811682
I got an error window that is empty....