Suchen:

Art: Beiträge; Benutzer: Vinny

Seite 1 von 20 1 2 3 4

Suchen: Die Suche dauerte 0,02 Sekunden.

  1. Antworten
    3
    Hits
    70

    Clarified to +/- from the volume change number.

    Clarified to +/- from the volume change number.
  2. Antworten
    3
    Hits
    70

    Hello Laith, The min / max change should be...

    Hello Laith,

    The min / max change should be set higher than the volume change.

    Min / Max values are the boundaries that tell the KHD by how much to adjust by WHEN the KH value is greater than...
  3. As mentioned above, the P4 does include a...

    As mentioned above, the P4 does include a power-loss monitor feature, but requires a backup power source to keep the vital equipment running.

    Within the P4 you can also configure the default...
  4. Antworten
    8
    Hits
    370

    Product dimensions are shown in the product page...

    Product dimensions are shown in the product page of our shop.
  5. Antworten
    2
    Hits
    93

    Hi, What is the firmware version running on...

    Hi,

    What is the firmware version running on the P4?
    Wi-Fi module firmware version on P4?

    The values shown in GCC and the app do not match?
  6. Antworten
    6
    Hits
    109

    The max supported distance between PAB-devices is...

    The max supported distance between PAB-devices is 100 meters.
  7. Excellent!

    Excellent!
  8. The lights require adequate room to disperse the...

    The lights require adequate room to disperse the heat.
    Using the lights in an enclosed area is okay as long as the space has fans to remove the heat.
  9. 1. In order for the P4 to control the LX7, you...

    1. In order for the P4 to control the LX7, you will need the PLM-PWC expansion card. This card is installed onto the P4 and allows for wireless communication between the P4 (MASTER) and multiple LX7s...
  10. Hello Laith, For the most coverage throughout...

    Hello Laith,

    For the most coverage throughout the entire tank footprint, I would do 5 fixtures positioned perpendicular to the tank length.
    This will allow you to not only place SPS anywhere in...
  11. Antworten
    2
    Hits
    143

    Is this MAXI unit the only GHL device? No other...

    Is this MAXI unit the only GHL device?
    No other doser is connected to this maxi doser?
  12. Antworten
    1
    Hits
    77

    Perhaps the internal vent tube is clogged which...

    Perhaps the internal vent tube is clogged which is preventing air from actually escaping from the VENT.
    You can verify this by opening the KHD and seeing if there is a small in-line filter blocking...
  13. Hello, After GHL Control Center is installed...

    Hello,

    After GHL Control Center is installed on your computer, you should be able to access the program folder in the C: drive.

    The ProfiLux 3 firmware file is located here:
    This PC -> OS (C:...
  14. What do you mean by "turn off"? Under what...

    What do you mean by "turn off"?
    Under what circumstances would these probes need to be "off"?
  15. Antworten
    8
    Hits
    370

    Yes and yes.

    Yes and yes.
  16. Antworten
    3
    Hits
    263

    When you connect, go to the general settings page...

    When you connect, go to the general settings page and look close to the bottom of the page. The channel and address numbering will be next to the Master/Slave/Standalone options.
    What are the...
  17. Which device are you using?

    Which device are you using?
  18. Antworten
    3
    Hits
    263

    Do you have any simulation features enabled?...

    Do you have any simulation features enabled?
    What is the address numbering you assigned to each light?
  19. Antworten
    1
    Hits
    115

    Hi there, The slave doser 2.1 would be the...

    Hi there,

    The slave doser 2.1 would be the best option based on what you already have.

    You will be able to connect this slave unit to the SA D2.1 if it is running separately from the P4...
  20. The PLM-PWC card can be used on both the P3 and...

    The PLM-PWC card can be used on both the P3 and P4. Both controllers require it if you want to have the ProfiLux control your LX7.

    When you install the card, you should assign all LX7s as slave as...
  21. Antworten
    9
    Hits
    2.201

    Coming soon.

    Coming soon.
  22. Antworten
    9
    Hits
    2.201

    Press the brush icon (top right) to enter...

    Press the brush icon (top right) to enter dashboard editing mode. Press the (+) icon, then select the tiles you wish to add.
  23. Antworten
    10
    Hits
    422

    Use the ALWAYS ON function for the socket that...

    Use the ALWAYS ON function for the socket that will have the dosing pump power plug connected.

    This will allow the dosing pump to always stay ON.
    If your dosing schedules are setup correctly,...
  24. Thema: leak sensor

    von Vinny
    Antworten
    4
    Hits
    346

    Sounds normal. See our video on setting up...

    Sounds normal.

    See our video on setting up leak sensors:
    https://youtu.be/KTA5V3j6Wig
  25. Antworten
    10
    Hits
    422

    Do as mentioned above. NOTE When you have the...

    Do as mentioned above.

    NOTE
    When you have the doser connected to the S1-S4 port, it will automatically be assigned to the S1-S4 switch channels by default.

    Since you currently have a Powerbar...
Zeige Ergebnis 1 bis 25 von 500
Seite 1 von 20 1 2 3 4