Hi,
Ideally the probes should be placed in an area where there are no microbubbles present. If that is not really option, an area with minimal microbubbles is the next best thing. You don't want...
Art: Beiträge; Benutzer: Vinny
Hi,
Ideally the probes should be placed in an area where there are no microbubbles present. If that is not really option, an area with minimal microbubbles is the next best thing. You don't want...
Hi there,
While you wait for a reply in your ticket, take a look at this article:
https://www.aquariumcomputer.com/knowledge-base/how-to-update-or-restore-wi-fi-module-firmware/
Since you are...
Hello,
If you haven't done so already, please email us directly:
sales@ghl-kl.de
Hello,
Please open a support ticket for assistance with this.
If you have an existing ticket for the repair case, you can reply to that to re-open the case.
Yes that is correct.
Hi Aaron,
If you do decide to grab that PB-6D (non-PAB), you will have to first re-number your existing powerbar outlet so they start at 7. This new PB will be assigned as 1-6 and the original PB...
Hi there,
Go to the PL settings page, choose an unused gate and set the function to AND. Select the illumination channel and pH control downward option. Assign this PL function to the outlet of...
The Y-piece can be used to connect your WC waste water and KHD waste water. The vent tube should be kept separate.
One RS232 device can be connected to the port at a time.
Hello Eli,
As long as the waste water tube is pointing downwards and runs no risk of sending water up the KHD waste tube during a WC, that would be fine. A Y-piece would probably be a better...
As long as the cable is designed for use with a GHL controller, yes. Otherwise, it would be best to use a BO box.
If no network is found, you have the option to manually type-in your network name and password.
Instructions for getting the doser connected to your Wi-Fi can be found here:...
Yes it's possible.
Use a PL-LY splitter cable.
Ruben,
Your screenshot shows you using GHL Control Center which is the incorrect software. It will not work this way because this software does not support the PII.
You should be using ProfiLux...
It should work fine.
Since each 1-10V port on the ProfiLux supports 2 independent illumination channels, you can set 1-10V ch.1 to Illumination #1 and 1-10V ch.2 to Illumination #2.
More info on...
As Gael mentioned, those are not genuine GHL probes. They also do not seem to have any markings to indicate what they are. It would be best to purchase new probes.
Did you read the "How to connect over USB" article?
There it provides you with tips and photos of what your device manager window should show. There is also a video showing how to manually install...
Hello,
Unfortunately, it is not clear which platform you are wanting to use (GHL Control Center or GHL Connect) to make changes to your P4's network settings. We do have an article in the...
Easy. :)
Create a new PL function where you select your current PL as Input 1 and the maintenance mode (Inverted) as Input 2.
Push notifications will be made available in a future update.
Please open a support ticket.
Check your chart settings and make sure you have selected the probes you want to see data for.
Hello Kasper,
It would be best to contact GIESEMANN for clarification on their "control" wire. The wires coming from the "1-10V" cable should be connected to the BO box. If you can post a photo of...
If you already have your ATO function setup (D2.1 pump for ATO), you would only need to create 1 Programmable Logic function which combines the existing ATO function with the maintenance mode which...
Ok.
It would be best to just leave the doser ON 24/7 so the KHD can make the adjustments for you. If you find that the KHD has to continuously reduce your dosages, then that will tell you your...