You're right, the max. power input for 60 cm is 33W, for 50cm it is 26W.
You can find the specifications here:
https://www.aquariumcomputer.com/en-GB/products/led-illumination/mitras-lightbar
Type: Posts; User: GHL Support
You're right, the max. power input for 60 cm is 33W, for 50cm it is 26W.
You can find the specifications here:
https://www.aquariumcomputer.com/en-GB/products/led-illumination/mitras-lightbar
Please post again all settings of the level settings/ details min-max-control /sockets - thanks.
Please understand that we can only provide this information for buying the fitting adapters (have a look at nominal width & thread): 7484
For the socket with the heater, you select "Temperature" as function and then "Heater".
For the socket with the fans, you select "Temperature" as function and then "Chiller".
In the temperature...
If you select "Fill water" as socket function, without "ATO only" - does it work then?
Hello again,
the latest possible firmware for Profilux Plus II is 5.17 (latest ProfiLux-Control 5.1.7.2).
In the download section you can find a manual for the firmware update of ProfiLux II:...
I think from what you describe you rather need the Min/Max control - look at this:
Min/Max control
Two sensors 2 work together to control a water level. Sensor 1 works as maximum-switch, sensor 2...
Hello Diane,
we recommend to send the unit in to GHL for checking.
Please contact your retailer for details regarding the return process - thanks.
For controlling a Mitras Simu Stick you usually need two L-Ports (L1L2 and L3L4, since you have 4 colors available).
If you connect the LED-Control1 to an L-port (e.g. via Y-splitter), then you have...
Hier auch noch ein paar Tipps zum Verbinden über USB:
http://forum.aquariumcomputer.com/showthread.php?633-Verbinden-%FCber-USB-bitte-zuerst-lesen!
If you think the probe is defective, then please contact your retailer for further instructions how to proceed in this warranty case - thanks.
What if you set the maximal switching time to 0?
Then there should occur no alarm at all.
Hello,
no, presently it's still not possible to perform the firmware update via LAN.
Hallo,
einen Fehler in den Einstellungen kann ich nicht erkennen.
Die Sensoren wurden ja richtig montiert (Nr. 3 oben als Max-Schalter, Nr. 4 unten als Min-Schalter) und wurden nicht invertiert,...
Danke für die Rückmeldung, wir werden das prüfen.
Hallo Herr Baron,
der pH-Anschluss an der Expansion-Box ist kein umschaltbarer Eingang und kann daher nur für pH verwendet werden.
Sie bräuchten die Erweiterungskarte für eine weitere...
@egosum:
Hier empfehlen wir ebenfalls, den ProfiLux zur Überprüfung einzusenden.
Für weitere Einsendeinformationen wenden Sie sich bitte direkt per E-Mail an GHL.
Yes, that should be correct.
Yes, the yellow LED should be on.
Yes.
What does the sensor show when you plug it into the calibration fluid after calibration?
Can you exclude that the calibration was not successful?
Could you post your dosing pump settings here?
Unfortunately there is no easier way - you have to make the re-setting in the ProfiLux.
We also suppose that the battery must be replaced.
Ja, natürlich.
Bitte wenden Sie sich an info@ghl-kl.de für weitere Einsendeinformationen.
Hallo,
der ProfiLux Plus II wird nicht mehr produziert.
Die höchstmögliche Firmware ist hier 5.17:
https://aquariumcomputer.com/de-DE/ghldownloads?fileID=181
Hello,
do you have already the user manual for LED-Control4 passive?
Here you can download it:
http://support.aquariumcomputer.com/german/section.php?sid=12