Search:

Hmm so one for one against :)

No thoughts on this?

HI guys,

Sorry if this has been asked before, but a quick search didn't yield any results. When I first set up my P3 I used the calibration fluid (x2) for my ph probe. Time has passed and I am...

Can you re-use the calibration fluid that comes with your ph probe? Or are they use once and throw away?

Thanks
Paul

Works perfectly for ATO and WC now, thanks again
Paul

Of course!

Thank you
Paul

Hi I'm having problems with my ATO+WC

I have 2 float level sensors and pumps for in and out on S5 and S6
In L1 set up I have 1 set to ATO+Water Change. L2 says Not enabled (normal)
Using default...

I asked a similar question of D&D, I have a Deltec Dc-750 Cooler

Message response below, that I'd like to share:-
Paul
I do not run my own cooler through my computer but David Saxby does.
If...

Youre quite correct, had a rouge timer from when I was playing, deleted it and now everything is fully functional

Thanks!

That did the trick!
Thank you so much :D
Paul

I'll check tongiht and report back, thanks for the tip
Paul

I have a profilux plus II, it running the latest firmware 5.00 (dated 110210) and the latest control program.

As far as I know no feed timer is active, in that I have not pressed Escape and...

HI There,

I have a tunze 6055, I have set my pump and voltage settings, but all it does is turn the pump on for 1 second every 30, I was expecing a sine wave flow.
Unplugging Tunze1 cable from...

Hi guys,

Can any one recommend and affordable calcium reactor setup where I can use my Profilux Plus II to make all the neccessary controls.

I have never used a Ca RX before so this is...

Yes I did try and load my old settings back, I misunderstood when it said they would have to be entered again.

Just to close the thread, my temp readings are back to normal.

I'm so glad I made a copy of my settings before I upgraded the firmware :)

Much releived
Paul

Thanks Matthias, that seems to have done the trick, I had to dash to work straight after so I'll check again from home, but it changed from 13c to 27c which is much more likely to be correct.

Paul

Thanks for coming back to me, yes I did see that, it makes no difference whether it's on or off the reading on the screen is still wrong, currently in my tank set to 26c and showing 13c on screen :(...

and here are the settings since upgrade

0, "CODE_SOFTWAREVERSION", 500
2, "CODE_PRODUCTID", 3
6, "CODE_SERIALNUMBER", 1001092047
10, "CODE_SENSORPARA0ITEM0", 700
11, "CODE_SENSORPARA0ITEM1",...

Couple of screen shots:

http://paulsfishtank.co.uk/photos/log.jpghttp://paulsfishtank.co.uk/photos/temp1.jpg

Erm, you've said search for the same value twice

SENSORPARA1ITEM2
SENSORPARA1ITEM2

Do you mean:
SENSORPARA1ITEM1 (notice the 1)
SENSORPARA1ITEM2

Or even 2 and 3?

I agree it does work perfectly in parallels, indeed this is what I am doing, but for a relativly simple application, it's a pain to load a whole windows VM just to run one small app in crystal mode....

Sounds simple enough, thanks
Paul

Hi there

My temp is stuck at 0.0c after an upgrade from 4.08 to 5
The settings import did not work stating there is so serial number in the import

the control program shows my s/n as...

Thanks to Chippypah and others on UR forum, it looks like 6055s or 6105 will do the job.