Suchen:

Art: Beiträge; Benutzer: johnfallon135

Seite 1 von 4 1 2 3 4

Suchen: Die Suche dauerte 0,00 Sekunden.

  1. Antworten
    2
    Hits
    756

    profilux 3

    profilux 3
  2. Antworten
    29
    Hits
    22.498

    but the first 2 you described are L1/L3 which are...

    but the first 2 you described are L1/L3 which are + and - and remaining 2 wires L2/L4 are also + and -

    10498

    which are the ones that light up the diode and does it matter which + order...
  3. Antworten
    29
    Hits
    22.498

    so I'm guessing the first 2 wires are live and...

    so I'm guessing the first 2 wires are live and the remaining 2 are dead wires? if so how do you tell the difference from the first 2 with a battery and diode does it matter which is + and - in pin 1?
  4. Antworten
    2
    Hits
    756

    defective profilux 3 screen

    is there a fix for this line at the bottom of my screen? thanks

    10496
  5. Antworten
    32
    Hits
    9.468

    the device itself doesn't ask for a update...

    the device itself doesn't ask for a update confirmation it just stays in its normal screen

    if this helps after i click ok on the error 41 message box this message box then pops up

    8587
  6. Antworten
    32
    Hits
    9.468

    thanks this worked to connect my profilux to...

    thanks this worked to connect my profilux to profilux control however when i click on File --> Firmware - Update Profilux then select the ProfiLux3_V629.mhx file the update begins but then at 99%...
  7. Antworten
    32
    Hits
    9.468

    i never said i was able to connect to...

    i never said i was able to connect to ProfiluxControl that's the problem here was that i COULDN'T connect to ProfiluxControl. This entire time vinny was trying to help me update my profilux outside...
  8. Antworten
    32
    Hits
    9.468

    when i click the connect button in the Profilux...

    when i click the connect button in the Profilux Control program it says "the connected profilux has a too low firmware version and can't be used with this version of profilux control" this is version...
  9. Antworten
    32
    Hits
    9.468

    thanks for helping me matthias. yes the profilux...

    thanks for helping me matthias. yes the profilux still starts with the firmware 5.14
  10. Antworten
    32
    Hits
    9.468

    thanks matthias my PL3 does enter bootloader...

    thanks matthias my PL3 does enter bootloader mode. when i take the power off then back on during the reset message the PL3 screen blacks out which i'm assuming is the bootloader mode? however i still...
  11. Antworten
    32
    Hits
    9.468

    hey vinny just wondering if you're looking into...

    hey vinny just wondering if you're looking into this as i was hoping to get it working by the weekend thanks!
  12. Antworten
    32
    Hits
    9.468

    8568 8569 during this time i unplug the...

    8568

    8569

    during this time i unplug the power to my profilux then plug it back in. also tried leaving the plug out prior to the reset message then plugging it back in during the reset message...
  13. Antworten
    32
    Hits
    9.468

    okay so i restarted my computer and tried it...

    okay so i restarted my computer and tried it again but it now says "ERROR!! No.001 Download error" at 3/7 of the download
  14. Antworten
    32
    Hits
    9.468

    thanks so i got everything working now but i get...

    thanks so i got everything working now but i get stuck on the flash programmer after i click full operation it says "please push reset button on user board" then i plug my profilux back in then it...
  15. Antworten
    32
    Hits
    9.468

    my GHL Control Center folder only contains: ...

    my GHL Control Center folder only contains:

    (Folder) GHL Control Center
    (Folder) Tools --> Flasher shortcut
    GHL Control Center shortcut
    Unistall GHL Control Center shortcut

    i searched my...
  16. Antworten
    32
    Hits
    9.468

    i connected the rs232 cable to my computer and...

    i connected the rs232 cable to my computer and under COM and LPT in the device manager it just says "prolific USB-to-Serial Comm Port (COM4)" with a exclamation mark and i updated it. it doesn't say...
  17. Antworten
    32
    Hits
    9.468

    i got my ip address however after creating a...

    i got my ip address however

    after creating a new connection in PC with my IP address it said the firmware is too low to connect.

    after creating a new connection in GCC with my IP it says...
  18. Antworten
    32
    Hits
    9.468

    5.14

    5.14
  19. Antworten
    32
    Hits
    9.468

    thanks vinny i got the usb however it says that...

    thanks vinny i got the usb however it says that my profilux III firmware is too old to work with my GCC.. how do i update it?
  20. Antworten
    10
    Hits
    3.293

    i understand the controller wirelessly tells the...

    i understand the controller wirelessly tells the pumps what to do just wasn't sure what was the point in the profilux vortech's controller's second pab port. why would someone want to hook the second...
  21. Antworten
    10
    Hits
    3.293

    what's the point of the second port on the...

    what's the point of the second port on the vortech controller then?
  22. Antworten
    10
    Hits
    3.293

    is 1 pab port good enough for 2 powerheads or is...

    is 1 pab port good enough for 2 powerheads or is each port on the controller for each powerhead? i noticed there's 2 ports thanks
  23. Antworten
    32
    Hits
    9.468

    thanks vinny is there a way to do it without the...

    thanks vinny is there a way to do it without the usb as i lost my usb cable i might just have to go out and get one.. also if i don't have my lan settings still set to automatically have an ip...
  24. Antworten
    32
    Hits
    9.468

    GCC not connecting to my profilux

    i connected my profilux directly to my modem via ethernet/lan cable however GCC just says not connected. is there a step i'm missing? how can i get GCC to connect/recognize my profilux III? thanks!
  25. is there a way to save my profilux III settings if it happened to be unplugged?

    i'm tired of inputting all my settings again after a power outage or moving my profilux to a different socket is there a way i can have the settings permanently saved? thank you!
Zeige Ergebnis 1 bis 25 von 87
Seite 1 von 4 1 2 3 4