Search:

Type: Posts; User: marcusbptan

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    6,636

    Cannot connect to Doser 2.1 from myGHL

    Hello,

    I've previously had flawless connection of my 2 Doser 2.1 SA via myGHL. Recently updated the GCC to 1.1.1.8 and the FW of the Doser 2.1 that is included in the update.

    Since then, I've...
  2. Thanks Vinny, My Doser 2.0 has lost wifi...

    Thanks Vinny,
    My Doser 2.0 has lost wifi connection and the new Doser 2.1 did not have the right IP address.
    I have reconnected them to wifi and will proceed with reactivation of myGHL. Fingers...
  3. Thanks Vinny, I didn't try as I was under the...

    Thanks Vinny,
    I didn't try as I was under the impression that myGHL and WiFi cannot be used together.
    I suppose I can turn off my GHL in GCC (via USB) and try?

    Cheers
    M
  4. Cannot connect new Doser 2.1 to my GHL and lost previous connection

    Hello,

    I have 2 issues with my Doser 2.0 and new Doser 2.1 (for 2 tanks), both firmware are up-to-date 1.24. In GCC 'systems' myGHL is enabled.

    1. Doser 2.0 was previously connected to myGHL...
  5. Hello Matthias, You are correct in that the...

    Hello Matthias,
    You are correct in that the dosing amount is too small. I have changed to daily dosing and the pump is now showing on the dashboard.
    Thank you.
    Cheers
  6. Dosing pump not showing in myGHL dashboard

    Hello,

    I'm looking for some advice and assistance. I am using Dosing pumps 1 and 2 (on Doser 2 SA) and pumps 5,6 and 7 (on Doser 2 Slave). Pump No 2 does not show up on the Dashboard, even though...
  7. Replies
    2
    Views
    2,399

    Thanks Vinny.

    Thanks Vinny.
  8. Replies
    2
    Views
    2,399

    Doser2- suggestions for running 2 tanks

    Hello,

    I'm setting up an additional reef tank.

    I currently use the Doser 2 SA and a slave unit on my present tank and it is controlled with GCC and via the iOS app. I really like it.

    The...
  9. Replies
    2
    Views
    2,406

    Thank you Vinny. I had a further look at GCC and...

    Thank you Vinny.
    I had a further look at GCC and corrected the refill amount.
    Cheers!
  10. Replies
    2
    Views
    2,406

    Doser Blinking Yellow

    Hello,

    After tinkering with my GHL Doser SA and Slave unit this evening, I noticed that the GHL logo is blinking yellow. I realise that it is a 'warning' blink but I cannot seem to trouble shoot...
  11. Thank you for the quick reponse Vinny! I have...

    Thank you for the quick reponse Vinny!

    I have reloaded the GCC and it worked.
    Unfortunately, I realised I have not entered the crucial set of saving the previous data into a file name. Hence, I...
  12. Help Needed - Problems after updating firware and myGHL activation

    Hello, I have encountered the following problems after performing these steps. I can't seem to think of a solution. Any advice and assistance is greatly appreciated.

    I'm at my wits end and...
  13. Replies
    2
    Views
    2,590

    Using iOS GHL Control app

    Hello,

    I am having trouble accessing individual dosing details whilst using the app.

    I have double tap for 'Dose Now', tap and hold the green fill bar to open 'Refill amount', double tap the...
  14. Replies
    10
    Views
    7,376

    Video of Blinking Indicator light and...

    Video of Blinking Indicator light and Intermittent Slowing Pump Head. This occurs with manual and automatic dosing.

    Blinking occurs at the start of the video 0 sec, then 9 sec, 10sec , 18 sec and...
  15. Replies
    10
    Views
    7,376

    Hello, I am experiencing a similar problem with...

    Hello,
    I am experiencing a similar problem with my 2 slave units, each have 4 pump heads. Both SA and PAB FW have been upgraded to v1.12.

    Screen shot below. I'll try and get a video of it and...
  16. Hello, Thank you very much for the update info. ...

    Hello,
    Thank you very much for the update info.
    Cheers
  17. Hello Matthias, Do you have any updates...

    Hello Matthias,
    Do you have any updates regarding the new firmware 1.10 for the Doser 2?
    Many thanks.
  18. Hello again, Do you have a time frame for the...

    Hello again,

    Do you have a time frame for the update to the FW to version 1.10?
    On which forum/GHL website will that announcement be made?

    Many thanks
    M
  19. Hello, Thanks for the quick reply. Cheers

    Hello,

    Thanks for the quick reply.

    Cheers
  20. GHL Doser 2 SA and Slave unit - Connection Problems

    Hello,

    I have 2 slave units and have connected them via the PAB socket to the SA Doser 2 in a 'daisy chain'. I cannot 'see' the 2 slave units nor can I assign or control their individual pump...
  21. Hello, Yes I use parallels. Many thanks for...

    Hello,
    Yes I use parallels.
    Many thanks for that info. I will update the firmware via a PC.

    Thanks for the quick response.
  22. Updating Doser 2 to New Firmware Error

    Hello,

    I have been unable to update my Doser 2 SA to the new firmware v1.0x.

    I have followed all the steps from an early pdf and have updated the driver etc and have the COM port identified...
Results 1 to 22 of 22