Search:

Type: Posts; User: Dimorb

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    1,116

    Do I need a specific cable/driver? It's USB-A...

    Do I need a specific cable/driver?

    It's USB-A to USB-A?

    Reason I ask is GCC crashes when I try to connect.
  2. Replies
    3
    Views
    1,116

    Reverse slave doser to master!?

    How do I reverse my doser 2.1 from slave mode to master mode when the assigned profilux 3.1T eX is no more available?

    Best regards

    Andre
  3. Replies
    7
    Views
    1,770

    Nobody knows what would happen if the vent hose...

    Nobody knows what would happen if the vent hose was submerged?

    Will it siphon water back to the aquarium?
  4. Replies
    7
    Views
    1,770

    I know this.. I was not intentional. It had...

    I know this.. I was not intentional.

    It had fallen down somehow. I have the waste and ventilation hose placed up on a grid over the drain. When I looked today it had found it's way into one of...
  5. Replies
    7
    Views
    1,770

    Hello again. I checked the test log and it...

    Hello again.

    I checked the test log and it seems like this have been a problem the last three tests. My sample volume is set to 100 ml.

    If this means that around 400 ml drain water have been...
  6. Replies
    7
    Views
    1,770

    Sorry for bad english / explanation. I ment...

    Sorry for bad english / explanation.

    I ment the tube going from the back. What would happen if that was beneath the water line?

    I think that the hose from the back may have fallen down into...
  7. Replies
    7
    Views
    1,770

    KHD siphon waste water from drain?

    Hello.

    When I checked my KHD today I noticed some odd measurements and went to check on the machine.

    All hoses where filled with water and I couldnt empty them. Found out that the waste hose...
  8. Replies
    3
    Views
    1,312

    Yes that would be the next step. But it's...

    Yes that would be the next step.

    But it's really weird that the volume in the tube are 46 and the doser doesnt fill it entirely even when calibration are the same.

    I use a graduated test tube...
  9. Replies
    3
    Views
    1,312

    Adding info. When calculating the entire...

    Adding info.

    When calculating the entire sample hose volum I get 46 ml - this is done by filling the entire line and dosing it into a measuring cup.

    When the line is emtpy I type in 46 ml...
  10. Replies
    3
    Views
    1,312

    KHD not working properly - What to do?

    Trying to setup a brand new KHD with doser 2.1 SA and connect to a Profilux 4. Everything is connected and setup as instructed in manual, doser set as slave of course, and setup mechanically....
  11. Replies
    2
    Views
    3,077

    How to remove PAB alarm notification?

    The PAB alarm went off when I was on vacation. A dose maxi had been drowned due to leakage.

    I've physical removed the device from the chain of connected devices but that does not remove/reset the...
  12. Replies
    1
    Views
    2,319

    Container "auto refill" all the time!!?

    I have some problems with my GCC.

    I use 7 different dose channels (doser 2 and 2.1) to dose into my aquarium. They are alla connected via PAB-Profilux.

    My problem is that when I am in GCC the...
  13. Doser Maxi Slave as a peristaltic pump feeding NO3 filter? - best solution?

    Hello everyone.

    I jump right in.

    I have a maxi doser that feeds my nitrate reactors (2 filters) with water. As for now I use the switch settings so that each motor starts and stops after a...
Results 1 to 13 of 13