Matthias
Why not allow people to select a list of reefs around the world to simulate? that way if you are in Greenland you don't get 20 Hours of sun light.
I would do tropical climates / belts...
Type: Posts; User: Vatso
Matthias
Why not allow people to select a list of reefs around the world to simulate? that way if you are in Greenland you don't get 20 Hours of sun light.
I would do tropical climates / belts...
The reason I wanted to do this was to try & mix my Kalk in my reactor more & try keep the PH stable.
so what I do now is run the ATO with a min time to run when activated so it mixes the Kalk...
I am busy working on a 24V output - 1 - 10V controller. I tried using a Pulse Width Modulation driver but it does not work on Resun Pumps!
So I used a relay connected to the relay out on L1 & L2...
It's it connected to the Profilux & being controlled by the profilux the sine wave & timing.
I do not use the Resun controller it's rubbish in my opinion
Wave using Resun Pumps & profilux
http://www.youtube.com/watch?v=y8z79qhap4A
Hi
what are the pins schematic for the float level sensor?
thanks
Thanks Frank
These options are great for T5 / LED lighting only units I have T5 / MH combo & am not sure that the clouds would make a huge difference when the MH are on.
I need to saw through...
Thanks Frank
I take it LED lights are what would be needed? do any of the rainy days / cloud cover work with light tubes / Dali?
Yes I have done this IE dali 1 = illumination 2 then I run thunderstorm manually on & it just switches the 0 - 10V on? & does not use the dali?
Can this be done?
do the rainy days / moon phase / thunderstorms work with Dali Ballasts?
I can't get the thunder storms to work the ballasts do dim as per the setup illumination
It's a II not an eX
what is the max number of sensors? one can have on that unit vs the others? what should he do upgrade to a 3?
Hi Mathias
He has a profilix 2 with 3 extra add on cards.
2 x Temp & humidity Cards
1 x Dali Cards
if he removes one of the temp cards he can then create a virtual temp probe.
he is not...
Hi there
I have a client that wants to create a virtual probe but is not able to unless he removes an add on card from his unit?
Please advise
Mark
Thank you for the reply Frank
I never said they were the same I was very aware that they are different & was in contact with the manufacture of the ballast who own the DSI protocol.
DSI was an...
I just tested it & it does not work :(
Will the dali card dim a DSI ballast I need to know before I buy the dali card
Thanks
Hi all I want to increase my PH using Kalk & ATO pump
I currently run it this way just as ATO
so I have set the following setup
G4 = water 1 or PH increase
G5 = G4 and delay 200s "that...
Where can we get such a thing?
I took the L1 / L2 port & made a module to take 1V - 10V in & that controls the pump with DC modulation
Yes - we were doing a Profilux Demo last weekend.
I made a unit to control an aquamedic pump
http://www.youtube.com/watch?v=gldvO1TlE8I&feature=player_embedded
thank you so much
it's fine I know what it does
if you set it low then the start off dim point is low & if you set the value high the dim start is brighter. was not sure what this function did
Thanks
Mark
What does this mean? min.dimlev.dali
thanks
Hi all
Someone I know had their ATO stay on when the power to their P11 went off "filled the sump with Kalk"? on my P3 the plug bar switches off when no connection to the profilux? is this not the...