Search:

Type: Posts; User: Guillaume

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    4,251

    8706 Here it is. It is currently connected...

    8706

    Here it is.

    It is currently connected to L1L2 port, but when I change it to L3&4&5&6, nothing changes on the controler
  2. Replies
    7
    Views
    4,251

    Hi, I doubled checked the settings. But I...

    Hi,

    I doubled checked the settings.

    But I don't get any reaction from the sensor. I tried configurating controls on the L3&4 and L1&2 ports... neither worked :(

    What options do I have ?
  3. Replies
    7
    Views
    4,251

    Dear Vinny, Thank you for your answer. ...

    Dear Vinny,

    Thank you for your answer.

    Unfortunately, the state doesn't change if I put in and out the level sensors (the 6 level sensors have the same X mark).

    The sensor has been cleaned...
  4. Replies
    7
    Views
    4,251

    I would also say that I tried to connect the...

    I would also say that I tried to connect the level sensor to the additional 4level card, slot 3, but this did not fix the issue. Where can I see if the sensor is sending any signal/information to the...
  5. Replies
    7
    Views
    4,251

    Level Sensor Issue

    Hi everyone,

    I am facing an issue with my auto-top-off function.

    The optical level sensor I have been using for several month does not seem to give any information to my profilux 3.1T.

    I...
  6. MyGHLID already assigned to another user ???

    Hi,

    I try to connect my profilux 3.1T to myGHL.

    UNfortunately, when I get logged in on myGHL, it asks for myGHLID and when I fill it in from the GCC, it says my GHLID has already been assigned...
  7. Thread: Android App

    by Guillaume
    Replies
    11
    Views
    7,856

    Hi, I downloaded v1.2 on my Android cell phone....

    Hi, I downloaded v1.2 on my Android cell phone. The program doesnt launch (freezed on a blue screen) any advice ?
  8. Replies
    5
    Views
    3,551

    Hi ! Yes, problem fixed, thank you !

    Hi !

    Yes, problem fixed, thank you !
  9. Replies
    5
    Views
    3,551

    Thank you very much for the tip !

    Thank you very much for the tip !
  10. Replies
    5
    Views
    3,551

    Firmware update - critical issue

    Hi,

    This is an emergency call for help.

    I tried to update my firmware with the GHL Controller PC software.

    The version of the new firmware is 6.23, for profilux 3.1T

    During the writting...
  11. Thread: PH trubble

    by Guillaume
    Replies
    15
    Views
    8,014

    Hi Artur and Lasse. Thank you for your answer. ...

    Hi Artur and Lasse. Thank you for your answer.

    I donnot find anywhere where I can see what probe slot is for pH and what slot is for conductivity on the expansion card. Both seems to be BNC slots....
  12. Thread: PH trubble

    by Guillaume
    Replies
    15
    Views
    8,014

    Hi, I also have a mesurement problem with my...

    Hi,

    I also have a mesurement problem with my extension card PLM-CondF-pH, installed on my profilux 3.1T.

    The cond. probe is not installed.

    The pH probe is callibrated with 7 and 9pH...
  13. Replies
    8
    Views
    5,766

    Thank you very much for your answer. I have...

    Thank you very much for your answer.

    I have another question : is the conductivity probe for freshwater (range between 0 and 2mS/cm) suitable to check R/O water ?
  14. Replies
    8
    Views
    5,766

    Hello PIWAWT I have been looking at your list....

    Hello PIWAWT

    I have been looking at your list.

    Are you sure I can connect 3 powerbar 5.1PAB to one Profilux 3.1T ? I could see only 2 slots (S1-S4 / S5-S8) for powerbars. :confused:
  15. Replies
    8
    Views
    5,766

    Hello ! Thank you very much for your answer. ...

    Hello !

    Thank you very much for your answer.

    I have a good overflow on the main tank (this aquarium is an elos aquarium, I never had any issue with the overflow), but the overflows on the...
  16. Replies
    8
    Views
    5,766

    New Controler System for several aquarium

    Hi everyone,

    I have a reef system made of 4 connected aqurarium, connected to each other; I would like to centralize the monitoring and control of the equipement.

    Does anybody knows the list...
Results 1 to 16 of 16