I was wondering about the logic needed to do this with one control outlet.
Have 1 gate function set for equal.
Set input 1 to temp 1 heater.
Set input 2 to temp 1 chiller.
I am asuming this...
Type: Posts; User: Luisagos
I was wondering about the logic needed to do this with one control outlet.
Have 1 gate function set for equal.
Set input 1 to temp 1 heater.
Set input 2 to temp 1 chiller.
I am asuming this...
I need to be able to rename voltage 1 and its value.
Like to change voltage 1 to Par Sensor and change the value to from 0-10 to 0-4000 for an example.
Worst case, please give us a ini file, that...
How many drivers you have hooked up to one channel?
The output can only handle 10ma. Those drivers pull a little over 3ma each at 10v.
I am using the same driver, but I have 2 drivers per...
Thankyou again.
Btw, you need a smiles that = Thank you Mattias.
Thank you Mattias.
Is there anyway to rename the voltage 1 or 2 to something else?
Example, I would like to see PAR Sensor, instead of voltage 1.
Thank you.
OK, I got LAN working by resetting my router. :)
Now, what does it mean examine hardware on bootup ?
Should I be worried about this?
Thank you.
It was not showing up when I boot it up.
I turn the power off and remove the adin card, rebooted the system. Turn power off again.
Put the adin card back in, and now it see it.
But this...
Thank you,
Whats the problem if i dont see "voltage 1 + 2" on the screen ?
I have the PLM-ADIN card plug in, and I don't see where I can program it.
What screen is the PLM-ADIN I/O located at?
I don't see any functions reference to it.
I just upgraded to P3 and I can not find the 2 analog Sensors inputs in the program, so I can use them.
I see the 4 digital sensors screen, but not the analogs.
Thank you.
You have a user name GooDFriend spamming PM with this junk.
"Hello friend, recommend you check your computer for viruses: http://**************.com/Luisagos "
Do not go to that link.
I understood you well. Just because something runs warmer not nessary means is out of spec.
These drivers are design to put out 48v at 1.25ma. By lowering the current to 1 amp, your running below...
LEDs are current devices.
At 48 v with 13 LEDS, your at 3.69 v per LED.
Running at 10v as the dimming voltages, your running at 1.25a.
The specs for the LED are 3.6v at 1000ma.
LEDs are...
These drivers run at 3.3ma at 10v.
3 of them should be the limit per channel.
I am about to start a thread on RC on using the meanwell drivers with Profilux.
I plan on using the EVG-AP-2F boards for the whites, blues, and lunar LEDs.
I should have full AI functions using...
Do you realize GHL has us spoiled!
Other controller users hope for new functions.
Profilux users just wait for shipping dates. :D
Thank you.
GHL is the best!
I am in love, :D
I was thinking, couldnt you use those digital inputs for switches.
Like more level sensors.
Start/Stop feed button.
If you know a little of electronics, just built a op amp circuit.
The circuit job is to translate 1-10 to 0-3.5.
I use to built these circuits a long time ago, i know it was cheap to make.
Use...
Remove sensor 2 and put a timer on sensor one. You need to calculate how long would it take to reach to sensor 2 level. You still have sensor 3 for back up.
That should clear one of the sensor up...
You may want to rethink about the 700ma, most powerful LEDS are running at 1000ma, to be able to reach the proper PAR levels.
Other then that, great product, looking forward for it.
Next month, they are releasing 0-10v analog in card.
Just need to find pressure sensors that have 0-10v output.
This is one example of many differant types of sensors.
...
I found these and they run off 120v
http://www.sylvania.com/BusinessProducts/LightingForBusiness/Products/Systems/DimmingandDaliBallasts/
It would be nice to able to hook up one of these to the new PIII.
Seagate FreeAgent 1.5TB