Search:

Thanks for you reply.

I know how to test it with my controller but I would also like to know if there is a way to test it without it to rule out any bad connections or cable problems.

--Mats

Hi,

I have a few Profilux 3 devices that use the optical level sensor. My problem is that they seem to fail after a year or two getting stuck in
the trigged position so it no longer detects a...

ok, thanks!

Regarding temp calibration. If I replace my temp sensor should I replace the calibration values for ADC1/ADC2 to its original values as they changed when I used the adjust temp setting in the PC app?...

Ok, thanks!

Is there any way to tell when it's time to replace a PH sensor? I have another older PH sensor that's been in service for about 4 years. Still seems to show a fair value and I...

Hi,

What is the life expectancy of the temp and PH probe? I've had the for a couple of years, noticed that the PH was a bit off and temp differed for about 1 deg C. After closer inspection I could...

Yep, I placed an order for it :)

Thanks
--Mats

I found that too, does it work with profilux 3.1N or the older 3?

Regards,

Mats

Hi,

I have a Profilux 3 and 3.1N unit. Is there an expansion card so I can connect more than 2 STDL4-4 powerbars?

I currently have 4 of them that I need to use.

Regards

-Mats

In my case the sensor was faulty, replacing it solved the problem. I choosed optical sensors as I was told they are more "reliable", anyone else that has experienced broken sensors?

--Mats

I'm kind of interested how the optical sensor works technically, what could make it partially work? What I've heard they're very reliable. I have an older Profilux 3 with a PL-0082 but that does not...

Another issue is that I had to leave for a week so I can now only access the device by remote. Anyway to restart it by remote or reset the sensors in any way?

One really risky way is to set the...

It reacts fine after a system restart or if I disconnect/reconnect it. It's no older than a year so it should be under warranty.
Just want to check if anyone experienced anything like this.
...

Hi,

I have a ProfiLux 3.1N with firmware 5.16. Recently my Level sensor used for water refill (Wat. fill(ATO) 1) stopped working. If the water is below the sensor nothing happens until i either...

Ok, thanks. Didn't realize that you could edit that column :)

--Mats

Ok, got it to work now thanks!

Earlier I could configure the delayed state of the sensor to minimize pump activity is that setting moved/fixed or removed? I can only find the maximum on-time...

Hi,

I'm a little confused about the level sensor settings in firmware 5.16. I recently upgraded my Profilux 3 from 5.11 to 5.16 and my auto top off level sensor went beserk.

I have only have...

Hi,

I've been thinking of upgrading my P3 with an expansion box or buying another one, I'm not sure yet. My situation is that I have a P3 for my main tank that works really well. I also have...

Ok, thanks for the info. Do you have any plans for a feeder? That's one of my future projects :)

--Mats

Hi,

I'm looking for a way to control custom low-voltage equipment from the Profilux. Is there any kind of SDK or general I/O boards available. I guess the Powerhub-6D-PAB is close to what I want...

Thanks for all the input, sorry for not responding until now. I have not had the time to test your suggestions yet. I have also ordered the controller from AI to test with for reference.

--Mats

Thanks for the input Christos!

Matthias, I have posted all the settings. I also have a .mov file that shows the problem but it's 80Mb, can I upload it to you in some way?

I have posted settings...

Ok, its the setting in the Illumination 1,2,3 etc.

Ok, the SOL units are just a few month old, do you need a serial number or firmware version? I was not aware that there was different models of...

Thank you very much for your help!

Another thunderstorm related question....Do I need to restart the Profilux when I have unchecked the thunderstorm box? I still get flashes when unchecked.
...

Ok, do you have any suggestion on how we proceed. Could you give me the spec. of the RS232 command that you send so I can try if my units flash from a terminal program?

I'll be happy to help you...