My tank consumption is quite low, just 2.8ml/dosage (total 33.6ml per day). I just wants to play safe as 7ml is more than double of my dosage. As I said before, the actual adjustment (1.5ml) is...
Type: Posts; User: Karytse
My tank consumption is quite low, just 2.8ml/dosage (total 33.6ml per day). I just wants to play safe as 7ml is more than double of my dosage. As I said before, the actual adjustment (1.5ml) is...
Yes, the KHD has made measurement after the change, and the adjustment shown on both the GCC and the APP are both 1ml. But I rec-checked the dosing chart, it actually show a +1.7ml adjustment.
I just started using the Add-on Control of the KHD. My nominal KH is set at 8 dKH, on the dosing pump for the KH buffer, these are the values I set:
When parameter deviates by this amount: 1 dKH...
Is Photo Mode available on LX6? If no, can someone tell me how I can setup one on my LX6? Thanks.
I have this error too, it happened after i updated the app to version 3.6.8
Yes, if you have a Standalone Doser 2.1.
I am using GCC 1.1.2.4 with P4 firmware 7.19. Can I upgrade to GCC 1.1.2.6 with P4 firmware 7.21 without installing GCC 1.1.2.5 (with P4 firmware 7.20)? Thanks.
Yeap, just once a week. It is the problem of my skimmer pump, it have some difficulties start up after switching it on and off, that's why i want to try it on 1-10V. Time for a new pump maybe :(...
Thanks Vinny.
I used this kind of PL before, but i don't want to switch on and off the pump that often, I am actually trying to see if the 1-10V interface have similar "delay on" after maintenance...
My skimmer pump is controlled by the 1-10V interface, which I configured it to operate at Minimum during maintenance mode. This maintenance mode is for manual water change, which turn off the return...
Thanks Gael and Pit. Will try yo find a proper connector for this. Just to make sure I am correct on the pin assignment, on this picture 10870, is the left most pin the Pin 1?
Thanks.
I made one using a RJ11 connector, but doesn't seems to working. Just wanted to be sure about the pin assignment, is this how it should be connected? The black cable goes to the "Positive...
I am a mechanical guy and really not good at electrical stuff. I have a RD5 controller, from the manual it said it can do 0-10V adjustment, using a earphone plug with the attached connection 10855...
I am considering getting the LX6300 for my tank, but have a problem on the mounting. The space between the back of the tank to the wall is just about 1 inch, so the Mitras Flex Mount System is not...
Matthias, this is the location of the probes.
9990
I also have P4, with 7.08 firmware and 6512 Wifi Module. The probes are all new, and without any extension.
This is what i received when this problem happened:
-----------
Temperature 1 : ...
I have similar issue problem too. Whether i got this false alarm, the temperature shown is always 40C.
Vinny, I tried re-assign the device but still didn't work. But after re-starting my router and moderm for a couple of times, myGHL suddenly back online. Really don't understand why this happened,...
Wifi Module firmware is 6512
P4 firmware 7.08
I disabled the blinking, I just switched it on and it's blinking white.
Not the GHL logo on the top of the P4, but the myGHL logo on the screen.
Can connect via GCC (Wi-Fi) and the app within the home network.
I suddenly cannot connect to the myGHL, it worked fine for the last 2 months, it just suddenly didn't work. I have restarted the P4, but still nothing. The myGHL logo is flashing on the screen. ...
The chiller is connected to Powerbar, and "Function" is set to be Temperature 1 (the temperature probe) and "Sub function" set to Cooler.
The chiller is turned on (by the P4) at 26.4C (25C + 5/6*1...
Thanks Pit.
As i am not using the Nightly change and also haven't set any alarm yet, so i think the equations should reduce to this:
Lower limit: Nominal -0.5*Hysteresis
Upper limit: Nominal...
Hello, i just got my P4 last week, just stared doing the setup
I am using TECO TK1000, the current setting is Nominal Temp : 25C, Hysteresis: 1C on the TECO. I should put these values into P4,...