Search:

Type: Posts; User: sphelps

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    2,823

    Nevermind, still switches back to non inverted....

    Nevermind, still switches back to non inverted. Just takes longer sometimes but it always switches back. Any help here would be great.
  2. Replies
    3
    Views
    3,980

    Solved, invert output.

    Solved, invert output.
  3. Replies
    2
    Views
    2,823

    Solved, disconnect drivers when inverting!

    Solved, disconnect drivers when inverting!
  4. Replies
    2
    Views
    2,823

    Inverse Program of LEDControl4

    Cannot invert output signal of LEDControl4 Passive. Running Firmware 5.10 on Profilux II Plus and Profilux Control 5.1.0.0

    With LEDControl connected to L1L2 and L3L4 an One LED driver connected to...
  5. Replies
    3
    Views
    3,980

    I should add got it working with this setup but...

    I should add got it working with this setup but the dimming control in profilux is reversed, LEDs zero output at 100% and LEDs full output at 0%.
    ...
  6. Replies
    3
    Views
    3,980

    LEDControl4 Passive with 0-5V PWM

    Is there anyone that can explain how to connect the LEDControl4 Passive to an LED driver that accepts a 0-5V PWM signal?

    This is the driver I'm working with:...
  7. Replies
    3
    Views
    2,749

    I should add got it working with this setup but...

    I should add got it working with this setup but the dimming control in profilux is reversed, LEDs zero output at 100% and LEDs full output at 0%.
    ...
  8. Replies
    3
    Views
    2,749

    LEDControl4 Passive with 0-5V PWM

    Is there anyone that can explain how to connect the LEDControl4 Passive to an LED driver that accepts a 0-5V PWM signal?

    This is the driver I'm working with:...
  9. Replies
    3
    Views
    3,593

    I have one level sensor in the mix which is in...

    I have one level sensor in the mix which is in the sump and controls the top off. When sump level drops the tank is topped off with saturated salt water or fresh water dependent upon tank salinity. ...
  10. Replies
    3
    Views
    3,183

    Couldn't you combine the cyclic function with the...

    Couldn't you combine the cyclic function with the delayed off function?

    Set cyclic to 15 seconds and delay off to 1785 seconds. That may or may not work, just a guess.
  11. Replies
    3
    Views
    3,593

    OK I think I got it figured out but if someone...

    OK I think I got it figured out but if someone with more experience could confirm no errors will result from this it would be much appreciated.

    Programmable Logic A = Water 1 AND Conductivity...
  12. Replies
    3
    Views
    3,593

    Water Change Programming Help

    Hello I'm looking for a solution.

    The aquarium has two water sources:
    1) Fresh water top off (socket x)
    2) Saturated salt water top off (socket y)

    There is a pump on timer A which removes...
  13. Replies
    2
    Views
    2,952

    Sweet! Thanks very much, I didn't know you could...

    Sweet! Thanks very much, I didn't know you could combine logics like that.
  14. Replies
    2
    Views
    2,952

    Skimmer on timer and feeding pause?

    Hi,

    I'm looking to setup my Protein Skimmer with the following conditions but I don't know if it's possible, so far I haven't been able to do it.

    1) Set to timer to only operate on 0.5 duty...
Results 1 to 14 of 14