Search:

Type: Posts; User: Kodo28

Search: Search took 0.00 seconds; generated 35 minute(s) ago.

  1. Thread: Measuring cell

    by Kodo28
    Replies
    5
    Views
    7,808

    You could use vinegar solution with RODI water.

    You could use vinegar solution with RODI water.
  2. Replies
    2
    Views
    4,511

    Make sure that the chamber is not full and also...

    Make sure that the chamber is not full and also check the vent tubing for the white filter
  3. Replies
    0
    Views
    1,222

    Kh director sample calibration

    Made some tests on the calibration process and I've found that the water sample calibration doesn't give me all time same numbers.

    water sample tubing is actually 83+16+12 = 111cm

    Calibration...
  4. Replies
    29
    Views
    28,378

    Changing the display unit value doesn't seems to...

    Changing the display unit value doesn't seems to change anything.
    I still have the timepoints reading by 30mn as set in Profilux with no fluctution between timepoints but sometime I dont have the...
  5. Replies
    29
    Views
    28,378

    OK, but then how do you explain for exemple on...

    OK, but then how do you explain for exemple on the Condx graph which there were no change between values of 3 timepoints of 30mn and those are well shown on the graph by 30mn periods and for some...
  6. Replies
    29
    Views
    28,378

    ....

    Ok but then why do I have for example reading points going down on values by half-hour interval but then at the last point it is showing by hour (My Profilux measurement period is set to 30mn) and...
  7. Replies
    29
    Views
    28,378

    Hi Vinny, there are a lot of little...

    Hi Vinny, there are a lot of little inconsistencies on the graph.

    They are some times accurate on time but not all the time and timing is not consistent between probes, all probes measurement...
  8. Replies
    29
    Views
    28,378

    Hi Vinny, I tested 15mn, 30mn and 1 hour...

    Hi Vinny,

    I tested 15mn, 30mn and 1 hour intervals, charts are still off of 8 hours and inconsistent. By changing, I got even worst discrepancies.

    Last point was at 03:00AM and actually time...
  9. Replies
    29
    Views
    28,378

    Also the charts are not showing consistent timing...

    Also the charts are not showing consistent timing points.

    example :

    05Aug showing 11:26AM next point is shown at 11:31AM (5mn) then next one only at 11:41AM and the next one later at 12:01PM...
  10. Replies
    29
    Views
    28,378

    Hi Vinny, The setting for the recording...

    Hi Vinny,

    The setting for the recording measurements is set to 5 minutes delay.
  11. Replies
    29
    Views
    28,378

    I am having the same issue... This is...

    I am having the same issue...

    This is happening since some time now. Running actually the latest versions of GCC 7.15 or Webinterface 1.0.7 but no changes.

    I am actually located in FRANCE and...
  12. Replies
    5
    Views
    15,744

    :) Thanks Vinny

    :) Thanks Vinny
  13. Replies
    5
    Views
    15,744

    Hi Vinny, Thanks for your reply ;) When I...

    Hi Vinny,

    Thanks for your reply ;)

    When I look at the power supply from the MP40 ,

    10943

    Is that Ok ?
  14. Replies
    5
    Views
    15,744

    Any Feedback from support on this ?

    Any Feedback from support on this ?
  15. Replies
    5
    Views
    15,744

    Ecotech MP40QD pump on socket 5 with switchable mode

    Can the Ecotech MP40QD pumps be connected into the socket 5 set in switchable mode on the PAB 5.1 without burning the mousfet fuse inside ?
  16. Replies
    5
    Views
    7,509

    Hello Matthiaf, Ticket has been opened under...

    Hello Matthiaf,

    Ticket has been opened under [Ticket #235] Connection to Gcc and IP address not possible
    Issue is happening again right now and connection was Ok yesterday night at 2:00AM.
    If...
  17. Replies
    5
    Views
    7,509

    I have been facing the same issue, like posted on...

    I have been facing the same issue, like posted on Facebook group...
    Every single day when I try to connect (first connection of the day) to GCC or locally using IP address, I am unable to connect...
  18. Thread: Redox

    by Kodo28
    Replies
    13
    Views
    9,912

    Well from what you have told until here, the...

    Well from what you have told until here, the issue happens on EB1 and P4. Probes are Ok and calibration fluid is new.

    If you are sure there is no interference's and that you are following right...
  19. Thread: Redox

    by Kodo28
    Replies
    13
    Views
    9,912

    The small differences between ADC1 and ADC2 looks...

    The small differences between ADC1 and ADC2 looks like the sensor doesn't read when plugged into the socket and inserted on the calibration. You said that the probes are working ok on the aquamedic. ...
  20. Thread: Redox

    by Kodo28
    Replies
    13
    Views
    9,912

    Can you post a screenshot from GCC Redox tab.

    Can you post a screenshot from GCC Redox tab.
  21. Thread: Redox

    by Kodo28
    Replies
    13
    Views
    9,912

    Normally at the moment when you save the...

    Normally at the moment when you save the calibration process, you should have 220mv which is the calibration fluid value and not 450mv.

    Did you tried to reinstall the firmware ?

    ADC1 on mine...
  22. Thread: Redox

    by Kodo28
    Replies
    13
    Views
    9,912

     Set the calibration tolerance  Determine the...

     Set the calibration tolerance
     Determine the Calibration value 2 and confirm with RETURN
     Plug the Null- plug ->RETURN
     Wait for the signal sound
     Disconnect the Null- plug and then connect...
  23. Replies
    3
    Views
    12,951

    No problem MatthiasF ;) Yeap it is what i have...

    No problem MatthiasF ;)

    Yeap it is what i have done meantime.

    Cheers!
  24. Replies
    3
    Views
    12,951

    tickets-enquiries signup not working

    Signup link to log Ticket-Enquiries is not working.

    Tried on Chrome and IE...Telling to many redirections...
Results 1 to 24 of 24