Plm-dali

Printable View

23.01.2020, 21:12
scrub29

Plm-dali

Hi I installed the dali card in my expansionbox but the system was not reconize it. Is this only possible in the P3/4?

I switch the card with a PLM-4L in my p3 and expansionbox. how can i find out with numbers the L card is?

thanks
24.01.2020, 16:10
MatthiasF

If you add or remove extension cards, you must re-assign the ExBox in the PAB-system. Otherwise the ProfiLux controller cannot detect the new card.
24.01.2020, 17:39
scrub29

Quote:

Originally Posted by MatthiasF

If you add or remove extension cards, you must re-assign the ExBox in the PAB-system. Otherwise the ProfiLux controller cannot detect the new card.

Hoi Matthias, I did assign the exBox again but the dali was invisible in de P3. but if I understand you correct it could work via the ExBox?
24.01.2020, 18:19
Vinny

Yes, that is correct.
All expansion cards which are supported is mentioned on page 10 of the EXB2 manual.
24.01.2020, 20:33
scrub29

Quote:

Originally Posted by Vinny

Yes, that is correct.
All expansion cards which are supported is mentioned on page 10 of the EXB2 manual.

Hi Vinny,

also the ExBox 1 1.09? in the manual its only talking about the 1.02 and no DALI is supported.
26.01.2020, 11:22
scrub29

Quote:

Originally Posted by scrub29

Hi Vinny,

also the ExBox 1 1.09? in the manual its only talking about the 1.02 and no DALI is supported.

no one?
28.01.2020, 09:36
scrub29

Quote:

Originally Posted by scrub29

no one?

Hi I'm busy with the install can anyone tell me if the DALI card also most work in ExBox 1 v1.09?

thanks
28.01.2020, 14:20
MatthiasF

After re-assigning the ExBox to the PAB-system, ProfiLux knows the extension card, but PLM-extension cards are only shown for the ProfiLux and not ExpansionBoxes.
The last card slot in the ExBox can only be used for analog cards. So use one of the other for the PLM-DALI.
In order to configure the PLM-DALI, you must insert it temporarily in the ProfiLux and use GHL Control Center (System->ProfiLux->PLM-DALI-Configuration ...). Afterwards you can re-install it to the ExBox with the stored settings.
01.02.2020, 15:43
scrub29

Quote:

Originally Posted by MatthiasF

After re-assigning the ExBox to the PAB-system, ProfiLux knows the extension card, but PLM-extension cards are only shown for the ProfiLux and not ExpansionBoxes.
The last card slot in the ExBox can only be used for analog cards. So use one of the other for the PLM-DALI.
In order to configure the PLM-DALI, you must insert it temporarily in the ProfiLux and use GHL Control Center (System->ProfiLux->PLM-DAIL-Configuration ...). Afterwards you can re-install it to the ExBox with the stored settings.

thx it worked.
26.05.2020, 14:58
AQUA-digital

Quote:

Originally Posted by MatthiasF

After re-assigning the ExBox to the PAB-system, ProfiLux knows the extension card, but PLM-extension cards are only shown for the ProfiLux and not ExpansionBoxes.
The last card slot in the ExBox can only be used for analog cards. So use one of the other for the PLM-DALI.
In order to configure the PLM-DALI, you must insert it temporarily in the ProfiLux and use GHL Control Center (System->ProfiLux->PLM-DALI-Configuration ...). Afterwards you can re-install it to the ExBox with the stored settings.

hello i can`t find this (System->ProfiLux->PLM-DALI-Configuration) in the GCC only in the PL. where is this?