Email setup for Profilux4 Sockets

Its nice to get periodic email with the status of the sockets.

But is there posible to get the discription for the sockets in the email as well ?
And the current that each socket is using ?
And is there possible to get the status for all sockets ? I have 23 sockets :D

Something like this:

Code:

---

S 1 : On returnpump 0.3A

---

The message i recive now:

Quote:

---

Profilux4 Sockets

---

Quote:

---

S 1 : On
S 2 : On
S 3 : On
S 4 : Off
S 5 : On
S 6 : On
S 7 : On
S 8 : On
S 9 : On
S10 : On
S11 : On
S12 : On
S13 : On
S14 : On
S15 : On
S16 : Off
S17 : On
S18 : Off
S19 : Off
S20 : Off
S21 : On
S22

---

Quote:

---

Originally Posted by Vega77

Its nice to get periodic email with the status of the sockets.

But is there posible to get the discription for the sockets in the email as well ?
And the current that each socket is using ?
And is there possible to get the status for all sockets ? I have 23 sockets :D

Something like this:

Code:

---

S 1 : On returnpump 0.3A

---

The message i receive now:

---

Yes, below is what I receive via e-mail for sockets. I could not get the "loop" function to work, so I had to code each socket. I also was unable to get values for amps. Maybe these bugs are fixed in the most recent update. I'll give the loop and amps a try again when I get time and will post if successful.

VSV Off
Ca Rev. Off
Heater 1 Off
Heater 2 Off
CaOH ATO Off
180 return On
55 return On
Refugium light On
Fan On
CO2 On
þ

Coding:

$$SWID[0]$$ $$SWIS[0]$$
$$SWID[1]$$ $$SWIS[1]$$
$$SWID[2]$$ $$SWIS[2]$$
$$SWID[3]$$ $$SWIS[3]$$
$$SWID[4]$$ $$SWIS[4]$$
$$SWID[5]$$ $$SWIS[5]$$
$$SWID[6]$$ $$SWIS[6]$$
$$SWID[7]$$ $$SWIS[7]$$
$$SWID[8]$$ $$SWIS[8]$$
$$SWID[9]$$ $$SWIS[9]$$

Best Regards, Bob

Quote:

---

Originally Posted by Vega77

Its nice to get periodic email with the status of the sockets.

But is there posible to get the discription for the sockets in the email as well ?
And the current that each socket is using ?
And is there possible to get the status for all sockets ? I have 23 sockets :D

Something like this:

Code:

---

S 1 : On returnpump 0.3A

---

The message i recive now:

---

I used this attached document for coding. note it could be outdated.

Bob

Attachment 9740

I didn't know anything about that docment and just had some basic stuff setup. I have now messed with it and it seems to work but the email length (not just the legth in GCC is quite limiting. So I have several emails:

1. Switch states

Switch states on $$DATE$$ at $$TIME$$

$$REPS[10][2]$$ $$SWID[x]$$ : $$SWIS[x]$$
$$REPE$$

2. Probe values

Probe Values on $$DATE$$ at $$TIME$$

$$REPS[5][0]$$ $$SENN[x]$$ : $$SENV[x]$$
$$REPE$$


3. Alarms (incl probe values)
* * * A L A R M - $$DATE$$ at $$TIME$$ * * *

$$REPS[10][5]$$ Alarm $$LCTR$$: $$ALMS[x]$$
$$REPE$$

$$REPS[5][0]$$ $$SENN[x]$$ : $$SENV[x]$$
$$REPE$$

I have a duplicate of the switches email set to also send in the event of an alarm so I should get alarms, probes and switches in the event of an alarm.

Thanks very much for the coding document Bstohrer. It is very useful. I can now get much more useful information from my emails on P4.


:o :o :o