Printable View
Hi all,
I'm thinking to replace my razor 300w with Mitras product but I'm thinking about that as my tank is 120cm wide and to cover it properly I need 2 Mitras pendant.
Looking at Mitras light bars 110cm it seems covering better my tank but......
Which is main difference using pendant Mitras or light bar?
How many and types light bars do I have to use to have right spectrum for deep acro sps tank population?
Any chance to fix to tank edges Mitras 6xxx pendant?
Regards
Andrea
Which are the measures of your tank?
You presently have 300 W in total above the tank that shall be replaced?
120x45x50h
Yes at peresent i have 300w
Quote:
Originally Posted by Carolin
...and news?
Regards
Hello,
for this tank size we recommend:
-2x Mitras LX 6200-HV, in order that the tank is equally illuminated (also the edges).
-2-3x Mitras Lightbar 120 Actinic or Deep Actinic (or a mix)
If you like to replace your 300 W, then 3 Lightbars would be necessary.
Regarding only the width of your tank, I would have recommended to start with 2 Lightbars.
At the bottom of this page, you can have a look at the Lightbar sizes again:
https://www.aquariumcomputer.com/en-...itras-lightbar
Quote:
Originally Posted by Carolin
Dear Carolin,
4 questions about your feedback:
1.- 3xLB + all accessories to be controlled by profilux compared with 2x 6xxx pendant has a really big price difference, so are these 2 possibilities comparable in term of quality and results for my tank?
2.- can I simulate same light scenario with LB and 6xxx or LB has limitation compared with LB?
3.- can you send me dimension of LB-Z-Holder as I need to calculate if 3 of them fits on my tank edge as from one side I have Tunze Overflow Box 1074 that reduce the space for the 3 LB_Z_Holder.
4.- in case is it possible to order to you dedicated LB-Holder based on my tank dimension and constrain?
Regards
....news from ghl staff?
Thanks
Hello,
the main difference regarding the price between the Mitras LX and the Mitras Lightbars is that the Mitras LX have their own controller integrated while the Lightbars need a ProfiLux to be controlled.
Also the Mitras LX can be addressd by radio signal (among each other as Master and Slave and also via the PWC-card by the ProfiLux).
The width of the Z-Holder is 10 cm, the height is 3 cm.
"in case is it possible to order to you dedicated LB-Holder based on my tank dimension and constrain?"
Do you mean if we can offer you customized holders? I'm sorry, this is unfortunately not possible.
>> Yes I mean having one single customized Z-holder for fitting 3 LB and a bit higher than 3cm as it is to much close to the waterQuote:
Originally Posted by Carolin
.....news?
I'm sorry but we don't offer customized Z-Holders.
Dear Carolin thanks for your feedback and for other questions in the previous post?Quote:
Originally Posted by Carolin
Dear GHL Staff where I can find LED color mapping for Light bars?
....I mean the how LEDs are distributed along the Bar?
Thanks for your prompt feedback
You can find all the specifications, including LED layout on the Mitras Lightbar here:
https://aquariumcomputer.com/en-GB/p...itras-lightbar
I am not sure if I understand the question correctlyQuote:
where I can find LED color mapping for Light bars?
do you mean how the LEDs are arranged?
every 1,25 cm is a LED, the RGBs and the high-power LEDs are alternating
Hi Matthias,Quote:
Originally Posted by Matthias
My question is related to comparison between Mitras 6200 pendant and light bars.
I have profilux 3 so to save money I'm thinking to change my present razor with your bars problems is that it is no clear from me the right mix of bars I have to use (type and qualtity) to match Mitras pendant color mix.
I mean from specs I see Mitras has white LEDs but I can't understand if bars have them or not. I want a bit of white for grow and because I do not like total blu look.
Can you suggest me the best mix of bars to match Mitras 6200 color spectrum?
My tank is 120x41x55h
Thanks
Inviato dal mio SM-G920F utilizzando Tapatalk
I suggest to study the technical page for the lightbars
https://www.aquariumcomputer.com/en-...itras-lightbar
And here is the comparsion page for the Mitras
https://aquariumcomputer.com/en-GB/p...tion/mitras-lx
Dear Gunther,Quote:
Originally Posted by Gunther
If I need to connect 2 or 3 light bars can I connect them using the heatsink aluminium frame? Do you have dedicated tool to do so?
Regards
Inviato dal mio SM-G920F utilizzando Tapatalk
Yo mean a mechanical connect to create a self-supporting bridge? I´m not GHL staff, but I think this isn´t possible.Quote:
If I need to connect 2 or 3 light bars can I connect them using the heatsink aluminium frame?
If I had to do so I would use a separate bar with the needed length and connect the lightbars to it
Yes i mean mechanical connection. Thanks in any case, from your answer I thought you are using light bars.Quote:
Originally Posted by Gunther
Any feedback from GHL staff?
Inviato dal mio SM-G920F utilizzando Tapatalk
I have one, but my tank is´that long so I use some kind of Z-holderQuote:
from your answer I thought you are using light bars
I would not recommend linking two or more light bars with a "self-supporting bridge". The weight of the light bars where one links to the other would be too heavy and may create some sagging.