Printable View
can be downloaded now
the token evaluation in emails has been improved
new: if several alarms are present they can be inserted in an email using a loop, e.g.:
$$REPS[10][5]$$$$ALMS[x]$$
$$REPE$$
it is possible now to use a token right behind another token
the description of the tokens has been updated ("userdefined webpages")
It fixed my empty email but did the level token chnage?
This is what I'm using:
$$LEVN[0]$$ - $$LEVV[0]$$
Output:
Level 1 -
Adding a retun ad the end of the message fixed the level issue
The main problem I have is that when I click test I get the email and its resolving all the tokens correctly etc, perfect. When I trigger a level alarm manually it doesn't send me an email.
The other minor issue I've noticed is that whilst $$ALMS$$ give you "no alarm - all OK" if there is no alarm currently, the loop code as follows just returns blank, not a major problem but nice little thing to tidy up :).
$$REPS[10][5]$$$$ALMS[x]$$
$$REPE$$
To add some extra info, I also created a conductivity alarm and that didn't work either. And I've tried it completely disconnected from the GHL and even pulling the network cable.
we check this
OK, I tested this and it seems as it works as expected
I defined 2 messages - one should be sent when alarm is "just over", the other when alarm is "just new"
both email were sent correctly
are your settings correct?
I have this for my email and I can confirm that the message in a real even is also not send:
message:
$$ALMS$$
S
$$REPS[32][00]$$ $$SENN[xx]$$ - $$SENV[xx]$$
$$REPE$$
I
$$REPS[32][01]$$ $$ILLN[xx]$$ - $$ILLV[xx]$$
$$REPE$$
S
$$REPS[32][02]$$ $$SWIN[xx]$$ - $$SWIS[xx]$$ [$$SWIC[xx]$$]
$$REPE$$
L
$$LEVN[0]$$ - $$LEVV[0]$$
it's set as a : Alarm Just New
If I disconnect my pad box, the P3 displays the error but no email are sent
Emails send perfectly when I click test so SMTP server settings must be fine.
I've just set up 2 emails exactly as you described. The email content is:
One triggers on Alarm - just over and the other on Alarm - Just new. I triggered a conductivity alarm by pulling the probe out of the water and I get no emails. Firmware is 5.05e and PC is 5.0.5.3.Code:Your GHL Profilux has activated an alarm. The current alarm states are as follows:
$$REPS[10][5]$$$$ALMS[x]$$
$$REPE$$
Sensors
$$REPS[32][00]$$ $$SENN[xx]$$ - $$SENV[xx]$$
$$REPE$$
Out of interest I assume "just over" means when the alarm is cleared?
A little more info again. I just set one to send at a set time and that didn't send either. I'm just about to remove them all and build one with no tokens and see if that works first.
Edit: Nope not even one without tokens is working and it did before I upgraded.
that's what I got when I had a temp. alarm:
I copied your examples here and they were sent automatically under all conditions. alarm new, over , cyclic, certain timeQuote:
Your GHL Profilux has activated an alarm. The current alarm states are as follows:
Alarm: Temp 1
Sensors
pH-Wert 1 - 3.33pH
Temperatur 1 - 15.5C
(over means alarm cleared)
are you sure the emails are working correctly in general on your systems?
*snif* my profilux doesn't even want to send email while I'm pushing the test button.
I don't even get an envloppe on the display.
One thing I should add is that I am using the En - Fr firmware
Hi Matthias
I definately get emails when I hit test so the email settings must be fine or it wouldn't be able to send me those emails surely?
For those who get the emails when they push test but not when a real alarm happens try unplugging the P3, waiting a few seconds then plugging it back in. A full reboot solved the problem for me late yesterday.