Profilux Compatible Return Pumps (high flow)

Im looking for a proper 0-10V controllable return pump. I purchased two Jebao Pumps (DCP), but those are not possible to be controlled by 0-10V anymore.

I know Red Dragon exists, but its quite a price, and I'm looking for a pump that can handle high head pressure (sump in cellar).

So any ideas here of pumps that can be fully controlled by P4, that can lift at least 4 meters @ 25mm return tubes (as the flow meter is 25mm thats the thinnest part of my return) and using a manifold, so looking for a pump that can do at least 10000-15000 l/h @ 4-5 meters. (that gives a bit slack of manifold etc) that CAN be controlled by 0-10V

AquaMedic DC Runner pumps work good with ProfiLux and they are not very expensive. If you like you can even buy pre-configured cables here http://shop.aquarienkontor.de/produc...oducts_id=1915

I don't have mine for very long, but I find it quite loud. They have a relatively high pitch whine. But then I also haven't really given my pump enough time to sttle down and vibration isolation could be better (all hard plumbing).

However, they only go up to 9.000l/h so a little outside of your range.

PS: I also went for the 1-10V control because I thought I need it. But the truth is, so far I have only set the speed with the pendant. A full control loop ought to be possible I guess, but outsite of what I can do with my small setup. (Measuring flow rates or water levels in the overflow)
And if I change pump rates, I disturb my overflow. I found the need wasn't really there.
But I suppose you have thought about the need of pump control via ProfiLux.

Hallo
An AquaBee pump would be a possibility. Instructions for the connection can be found in the appendix, but only in german. But you can use Google Translation

Attachment 9590

Regards Pit

So it's not possible to control Jebao DCP 8000 PUMP with P4 ??

No, because it does not seem to have any 1-10v input connector on the driver.

Quote:

---

Originally Posted by sabarish

So it's not possible to control Jebao DCP 8000 PUMP with P4 ??

---

Yes, you can with this: "AquaLink A1" (third-party seller)
Attachment 11916

Quote:

---

Originally Posted by itsmorefun

Yes, you can with this: "AquaLink A1" (third-party seller)
Attachment 11916

---

are You sure that can go with this?
Jebao 15000 ?
Have picture of connecting?

Quote:

---

Originally Posted by anatimi

are You sure that can go with this?
Jebao 15000 ?
Have picture of connecting?

---

Please full reference. DCP DCT DCS DCA, etc... ???
Read the a1manual.pdf

i read but on site is write that is work for apex ...not for profilux so that was my question?

Quote:

---

Originally Posted by anatimi

i read but on site is write that is work for apex ...not for profilux so that was my question?

---

It work with 0-10v control. You only have to adjust cable pin and connector to Profilux pinout, i have 4 AquaLink A1 working well with my profilux.
If you are unable to do yourself a RJ45 to RJ12 connector buy PL-1680 https://www.aquariumcomputer.com/pro...oxes-adapters/

Hi
Can you please help me with the cabling? Aquamedic has 2 strips of wires in the cable for 0-10v. However the breakout box by GHL has 6. Where to connect what and will only 2 wires from Aquamedic will do?

https://www.aqua-medic.de/index.php?...t&id=461&cid=3

Regards

Sharafin,

First you need to identify which cable is your neutral and which is giving out the 1-10v signal.
Info on the cable colors can be found here:
https://www.allaboutcircuits.com/tex...s-infographic/

Neutral connects to the GND port
1-10v wire connects to the 1-10v port

More info on the breakout box can be found here:
https://www.aquariumcomputer.com/dow...ut-box-manual/

Hallo Vinny,

Habt ihr den AQLink A1 auf CH1 oder CH2 angeklemmt?
Ich will eine Jecod Pumpe DCP6500 mit dem Profiluxausgang 1-10V ansteuern.
Bin mir nur nicht ganz sicher ob CH1 oder CH2.

Lg