1-10v port's pin configuration

Printable View

26.03.2010, 03:11
M@rine Lover

1-10v port's pin configuration

Hi Matthias

May I know what is the pins configuration for the 1-10v port for ProfiLux Light controller?

I need it to connect my dimmable LED driver correctly.

Please kindly advice.

Thanks.
James.
26.03.2010, 08:58
Matthias

Hi James

the pin assignment can be found in the EVG-AP manual here:
http://www.aquariumcomputer.com/Down...G-AP2_V400.pdf
26.03.2010, 10:27
M@rine Lover

Quote:

Originally Posted by Matthias

Hi James

the pin assignment can be found in the EVG-AP manual here:
http://www.aquariumcomputer.com/Down...G-AP2_V400.pdf

Which pin should I connected to the dimmable driver's positive and negative dimmer line?

pin 2 & 3 or 5 & 3 or otherwise?
26.03.2010, 11:11
Matthias

2 & 3 if using channel L1, 5 & 3 if using L2
27.03.2010, 15:13
M@rine Lover

What is pin 4 & 6 use for :rolleyes:?
29.03.2010, 08:32
Matthias

additional signal for switching off relays at 0% brightness
29.03.2010, 13:12
almost

L1 & L2 goes from 1 telepfone jack.
Lets say that in that jack there are 6 contacts, starting from left to right numbering 123456 (as in the picture bellow).

http://inlinethumb22.webshots.com/26...600x600Q85.jpg

Can you tell me which numbers are:
+10V for L1
Grd for L1
+10V for L2
Grd for L2

I want to make the jack so to connect 2 dimmable ballasts to dimm 2 T5 tubes.
29.03.2010, 19:30
Blahenazo

small remark: L ports only have 4 contacts so your numbering would be 1,2,3,4 :-)

S ports do have 6 contacts
30.03.2010, 08:21
Matthias

Quote:

L ports only have 4 contacts so your numbering would be 1,2,3,4 :-)

- this is not correct - all 6 pins are used for the L-ports

pin 1 is on the left (view from rear)
30.03.2010, 17:07
Blahenazo

Quote:

Originally Posted by Matthias

- this is not correct - all 6 pins are used for the L-ports

pin 1 is on the left (view from rear)

oops, indeed it are 6 pins , don't now why I was under the impression that it was 4 pins.
my humble apologies :)
31.03.2010, 01:27
M@rine Lover

Hi Matthias,

Is pin 1, a constant output 12v supply or can be controlled?

Regards
James
31.03.2010, 08:02
Matthias

Quote:

Is pin 1, a constant output 12v supply or can be controlled?

is constant 12V
02.04.2010, 01:58
M@rine Lover

Quote:

Originally Posted by Matthias

is constant 12V

12V of 800mA;)?
12.04.2010, 13:02
almost

O.K.
I understand now how they should be connected but I order 3 of EVG-AP2 PL-0058 (I wanted shut off in 0V).

Every EVG-AP2 can controll 2 ballasts and I use ballasts which controll 2 lamps, so, in every EVG-AP2 4 lamps can be dimmable (2 pairs), correct?