PDA

View Full Version : what should i buy



yossix
19.08.2014, 15:33
hi.
i'm going to buy the ultimate pack. which parts do i have to add to this pack for my aquarium?
i have 2 tunze stream pumps (6105)
i have a giesemann infiniti light with 2X250 MH and 4XT5 with dimming ability (only the T5).
can i use the tunze osmolator (3155) with the profilux?
how long is the temp probe cabel?
thanks

GHL Support
20.08.2014, 14:05
i'm going to buy the ultimate pack. which parts do i have to add to this pack for my aquarium?


i have 2 tunze stream pumps (6105)
You need 1x Tunze cable 1, 1x Tunze cable 2 and 1x YL2 (splitter)


i have a giesemann infiniti light with 2X250 MH and 4XT5 with dimming ability (only the T5).

The MHs can only be switched on/off by our switchable sockets, the T5 could be dimmed through our 1-10V-interfaces.
You will probably need an adapter to connect the T5. Here you could use our LBF-AP (one offers two channels).
If the lamp is without internal shut-off (probably), then you will also need a GHL socket in order to switch off the lights completely at night.


can i use the tunze osmolator (3155) with the profilux?

If it can be used by being switched on/off by one of our switchable sockets according to a pre-defined condition, then yes.


how long is the temp probe cabel?

It is 3m, we also offer an extension cable in 2m or 5 m.

yossix
20.08.2014, 18:05
"The MHs can only be switched on/off by our switchable sockets, the T5 could be dimmed through our 1-10V-interfaces.
You will probably need an adapter to connect the T5. Here you could use our LBF-AP (one offers two channels).
If the lamp is without internal shut-off (probably), then you will also need a GHL socket in order to switch off the lights completely at night."

so how do i connect the T5?
it has 2 plugs to the 220 V and 2 pairs of wires for the 1-10V
so i connect the plugs to the power bar and the wires to the LBF-AP?

keneil01
20.08.2014, 19:22
Yes, plug, program and play :-)

6498


Sent from my iPhone using Tapatalk

GHL Support
21.08.2014, 10:23
@yossix: here the manual of the LBF-AP, hope then it will get more clear

6503

yossix
22.11.2014, 23:01
how many power bars do i need?
i got with the set 1 6d-pab and i need more sockets for on-off (skimmer,heater).
which another power bar should i buy? 6d-d? stdl4-4? 6d?
thanks

GHL Support
24.11.2014, 09:11
In principle each powerbar type is possible, it also depends of course on the number of sockets you need.
If you buy a Powerbar6D-PAB, you can connect it to the PAB-port and don't have to use a S-Port
which you could still use for a Dosing Unit etc. later on.

yossix
24.11.2014, 19:26
are there any differences between those bars?

Gunther
24.11.2014, 22:32
are there any differences between those bars?

The PAB version is able to measure the current and the possible cable lenght for PAB is highter (~100m vs. ~10m for the -D)

yossix
25.11.2014, 16:56
so for on/off functions (heater,ozonizer,UV) the STDL4-4 will be o.k. with the 3.1T-EX?

GHL Support
26.11.2014, 13:47
Yes, this will be no problem.