View Full Version : Manual
After fitting my PLM-PWC card iv noticed that the cloud and moonlight simulations no longer work, I have these set up as I think they should be but obviously something is wrong.
Where can I find the revised setup manual now that the software has gone through so many changes and the cards have been fitted.
Can you post some screen shots of the illumination channels etc so we can all chime in :)
5820
5821
5822
5820
Also, in photo 2, if I hit the flash buttons, nothing happens?
GHL Support
24.04.2014, 10:04
Have you made the corrsponding settings in each affected illumination channel (i.e. have you set a check mark each for Clouds and Moon in the simulation box)?
"Also, in photo 2, if I hit the flash buttons, nothing happens?"
-> Are you using ProfiLux Control version 6.0.6.0? Then we are already about to check this function.
Have you made the corrsponding settings in each affected illumination channel (i.e. have you set a check mark each for Clouds and Moon in the simulation box)?
"Also, in photo 2, if I hit the flash buttons, nothing happens?"
-> Are you using ProfiLux Control version 6.0.6.0? Then we are already about to check this function.
Yes the darkened by clouds tab is ticked in illumination channels 1 to 9 .
Depends on moon phase is ticked on illumination 2 for moon lights.
Yes I am using version 6.0.6.0
GHL Support
24.04.2014, 15:37
Ok, we will check this function as well.
Matthias
03.05.2014, 09:39
Hi
I tested it (again) and all works as it should.
Please make sure you use the newest firmware (ProfiLux 6.06, Mitras 1.16) and Software, I recommend GHL Control Center 1.0.4.5
Matthias
03.05.2014, 09:40
in regards to the manual - the update is on work, will be uploaded this weekend
Hi
I recommend GHL Control Center 1.0.4.5
Should I do away with the profilux control now then Matthias, iv also noticed that I can't connect wirelessly to the mitras, but can to the profilux with the GHL control centre.
I have just checked and have all the versions you suggest, moon lights and clouds are defiantly not working, should they be according to my screenshots above please.
Matthias
03.05.2014, 13:55
you can't connect to the Mitras wirelessly, you connect to the ProfiLux and the ProfiLux sends the illumination commands to the Mitras
-> all illumination settings have to be done in the ProfiLux (with GCC or ProfiLuxControl)
Mitras is then slave (did you adjust this in the Mitras? - direct USB connection required) and the ProfiLux is master
your screen shots say not much
Yes, profilux is master and all 3 mitras are slave
Profilux is master on address 1
Mitras is slave on address 2
Mitras is slave on address 3
Mitras is slave on address 4
Matthias
03.05.2014, 14:20
you didn't post the illumination channel settings (here: illumination 1 ...9 is of interest)
there the check marks for the simulation must be set
I am talking about the ProfiLux settings
https://www.dropbox.com/s/bs91feolqc7xvm4/Screenshot%202014-04-23%2014.21.39.png
Do you mean this one, I have ticked them all in each channel now.
Matthias
05.05.2014, 07:24
yes, this should work
problem solved now?
please post pictures here and don't link to another server
yes, this should work
problem solved now?
please post pictures here and don't link to another server
Should work but isn't lol
No
Ok sorry
Right, if I watch the light % on the web server! I can see it ramping down and then back up again as a cloud should be passing, however, there is no change on the lamp, I have set max darkening to 90% but I can see no change.
Also look at the hyper violet in the 2 pictures supplied, on the web server and on the touch, the hyper violet is showing at 37%, on the lamps, (all three), it's showing at zero, how can this be.
Also please note the hyper red in the first photo, there is no reading on it, I have all channels no 1 - 9 set to show.
Lastly, the flash buttons in illumination/thunderstorm, still do not work.
5863
5864
5865
Matthias
08.05.2014, 07:33
ok, so many posts, let us summarize
1. what are the exakt firmware versions of Mitras and ProfiLux, what ist the version of GCC (I assume you use GCC for setting everything):
2. post (here) screenshots:
- Mitras General page
- ProfiLux General page
- one ProfiLux illumination channel in question
- system page of ProfiLux
3. In GCC, being connected to ProfiLux: Is the Mitras reacting when you activate "test illumination run" and move the time slider in the light composer?
Went for a chat with Steve at Reefdreams yesterday, it seems I had the 0=off setting to low, iv put it at 30 and it's working ok, how do I reduce the frequency of the clouds Matthias please.
Thanks Steve for your help, thanks Matthias so far for your help
Matthias
09.05.2014, 06:50
change the cloud settings according to the manual (new version in download section)
change the cloud settings according to the manual (new version in download section)
I can't find it, can you post a link please.
Matthias
10.05.2014, 08:30
http://forum.aquariumcomputer.com/downloads.php?do=cat&id=7
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.