View Full Version : feeding pause
Hi,
I programmed the ptc (to silent mode) and accidently the pumps where still connected now they will not stop when i give a feeding pause alltough in the plc the status is 0%
anyony familier with this=
many thx
Matthias
20.03.2012, 11:57
what do the pumps have to do with PTC?
please more details
Hi Mathias,
I have 4 tunze streamers conected on a pIII< i dont know the anwser on your question but I do know sins i programmed the ptc the pumps i cant control anymore (i think they run on full speed) but the plc says that the waves are still working but it doens't. I set everything back to default settings and set back the back-up with no result!
thx
Matthias
20.03.2012, 18:03
show us a screenshot of the 1-10V-settings
Matthias
21.03.2012, 07:48
this is a very tiny screen shot, hard to read anything
if I am not wrong the interfaces have these assignments:
l1 = current 1
l2 = current 2
l5 = current 3
l6 = current 4
is this right, is that what you wanted?
then at least these settings are correct
-> if so then then check the current pump settings
what pumps are connected there? and how? how do you want to achieve the feed paus shut down?
please give us more detailled information, we can't help otherwise
Hello,
Before i programmed the ptc fan (l13/14) there was no problem, I have tunze streamers (6105) who worked fine.
if you need more information please let me know I can also call you no problem! e.brouwers@chello.nl 2350
Matthias
22.03.2012, 08:34
I can't read anything on the screenshot, please higher resolution
Hint: If you use <ALT>+<PRINT> instead of <PRINT> you will get a screenshot from the window on top only
Matthias
22.03.2012, 17:22
and how are the pump-settings? especially the behaviour during feed pause?
2358 both groups are the same
Matthias
23.03.2012, 08:10
enable "pump completely off during feed pause"
Hi I did enable it but it stays the same i will not go off or go from 50 to 75 % like i programmed it! it just goes on full speed on all pomps!!
Matthias,
Do you know what to do now?
thx
Matthias
26.03.2012, 13:18
so when you enable feed pause this happens:
1.) ProfiLuxControl shows 0% flow for the pump in question
2.) the 1-10V interface shows 0V
3.) but the pumps do not react at all
is this correct?
Matthias
26.03.2012, 19:13
do the pumps react at all to the wave patterns?
No just run on full speed
When I shut down the profilux the pumps still run on full speed
Matthias
27.03.2012, 11:39
I think there is a problem with the hardware, with the cables or with the pumps, it doesn't look like a settings problem
final test:
set the function of the L-ports where these pumps are connected to illumination 1 ... 4, each L-port to another illumination channel
save this
then go to light scenarious and change the brightness manually
this brightness change affects the L-ports: can you control the pump speed in this way?
Hello,
I still can't controle it i think you are right about the hw of the frofilux, what most I do know?? I bought the pIII 30 march 2011 and the expansionbox 12 may 2011!!
plz help me out! I can send you de receipt if you like!
Matthias
27.03.2012, 20:21
Hi
please contact your retailer if you think the unit is defective, he will give you further information
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.