Webserver & LAN settings input (router too)

[BigAl07]

Ok I'm up the the point of trying to set-up/access my P3 remotely. I like to think I'm fairly knowledgeable in regards to Computers in general but I'll admit the remote access portions are puzzling to me. So here is what I have


P3 connected to my DAP-1522 Bridge connected to my WLAN and accessing the P3 inside my WLAN from my laptop.
No email configured yet
No webserver configured yet.




Here are the screens that I'm puzzled on

A) System Screen (self explanatory)
http://i217.photobucket.com/albums/cc265/BigAl07_01/Equipment/GHL%20ProfiLux%20Controller/GHL%20P3%20Setup/GHL_System_screen.jpg



B) LAN Properties Screen (No idea what needs to be input here)
http://i217.photobucket.com/albums/cc265/BigAl07_01/Equipment/GHL%20ProfiLux%20Controller/GHL%20P3%20Setup/GHL_LAN_Props.jpg


C) Webserver Admin Screen (pretty simple yes?)
http://i217.photobucket.com/albums/cc265/BigAl07_01/Equipment/GHL%20ProfiLux%20Controller/GHL%20P3%20Setup/GHL_webserver_Admin.jpg

D) Port Forwarding Input screen for my CISCO E1200 Router
http://i217.photobucket.com/albums/cc265/BigAl07_01/Equipment/GHL%20ProfiLux%20Controller/GHL%20P3%20Setup/CISCO_PortFWDING.jpg




So basically what information am I missing and where do I locate the information I'm missing?

1) Port Forwarding - What "Application Name" (If I pick TFTP Ext port 69, Internal Port 69, Protocol UDP, To IP Address 192.168.1.0 are all entered automatically. Do I need to change these settings?) I suppose I need to check the box labeled "Enabled" as well correct?

2) In the LAN settings(pictured below) - What do I need to input and where? Where do I get the info to go in there?
http://i217.photobucket.com/albums/cc265/BigAl07_01/Equipment/GHL%20ProfiLux%20Controller/GHL%20P3%20Setup/GHL_LAN_Props.jpg

[Wirus]

1)
Application - first free editable row: Profilux Aquarium Computer
External port: 80
Internal port: 80
Protocol: Both (TCP only also should be ok)
To IP adress: 192.168.1.111 (unsing not yet used one between 2 and 254 is o.k. - and 111 is easy to remember)
Enabled: Yes

If you want to use PLC from outside, a second row with same settings but with port 10001 is neccessary

2)
Check "Use following settings"
IP adress: 192.168.1.111 (the one we forwarded at 1)
Subnet mask 255.255.255.0
Default gateway: 192.168.1.1
DNS: 192.168.1.1
NTP timeserver
Domain: north-america.pool.ntp.org [any other is possible, but this should fit best for you]
Timezone: UTC-5 (http://de.wikipedia.org/wiki/UTC−5) is the one for North Carolina, USA
Update interval: depends you you - I use 30min and think it´s o.k.
External web adress: <your DYNDNS or from another dynamic web address provider given link adress> linke myaqualium.dyndns.info

[chercm]

Tried to use the setting but kept hitting on the Router admin page , any idea?

[Wirus]

any idea?

How would it be to read the router manual?

[chercm]

How would it be to read the router manual?

Tried reading but does not work

[Wirus]

You tell us, you are not able to set up your router. You also don´t give us any information about that device or what´s the problem.

So how anyone should be able to help you?

[chercm]

Thanks I finally got it working

[Blahenazo]

ach nice to see that we could help :)

[chercm]

could we post this as sticky and in the PLC 5 thread so that it can help the rest ?