MAKDENTAL
04.02.2011, 10:27
Hi I’m confused with what to order,
I want to monitor /measure, pH, Redox, Salinity:
I also want to control Tank temperature, & Dedicated fish room ambient temperature/ humidity (possibly to switch an external fish room vent fan) if I connect to a plug bar?
And so I will have the following probes: PL-0071, PL-0093, PL-0054 PL-0094, PL-0279 and their respective calibration solutions
I will want to control the timing and power of two Tunze Turbelle in tank pumps and so will need the following cables and splitter: Tunze Kit (includes tunze cables 1&2 with splitter) not sure of order code no I’m guessing PL-0087,Pl-0088 & YL1-2 splitter –please tell!
So far fairly easy!
I also want to be able to stop my main system Eheim return pump (from sump) when the above Tunze pumps are in “feeding mode” what type of plug bar will that plug into? I presume it then needs adding to the programming for feeding ? will that be easy to do?
I have some TMC Aquaray lighting: 3 1500XG tiles and 2 twin Aqua-strip 600’s I will want to dim and time them for sunrise and lunar mode if possible?
I gather that I will need to put a LEDControl-1 between each light and power module, so I will need 4 of these for the 2x twin strips, However the max rating for this GHL item is 700mA at 20V and somewhere I read on a forum it mentioned I would need 2 for each 1000 tile. Please correct me if I’m wrong as the XG1500 tiles are half as much again? and so do they need 3 GHL modules each making a total of 9 plus 4 (for the strips)? How are these connected? It’s important that the tiles are fully powered to get maximum punch/PAR! These items will need power bars digital or analogue? What’s the difference? How many of each will I need?
To future proof I will want the ability to connect later “4” dosing pump, possible a sump LED light, possible GHL storm LEDs and so will need enough sockets for this possibly more Tunze Turbelle pumps !
Obviously a profilux 3 ex based system with a special offer variant - which one ? what how many power bars? Do pumps/ lights that are GHL controlled via special cable need mains power from a power bar or will any socket do?
Lots of questions but difficult to find information that is not confusing!
With all this in mind can you list the order code numbers for me showing the power bars needed and what extras I may need if go for the future bits as well?
Mike
I want to monitor /measure, pH, Redox, Salinity:
I also want to control Tank temperature, & Dedicated fish room ambient temperature/ humidity (possibly to switch an external fish room vent fan) if I connect to a plug bar?
And so I will have the following probes: PL-0071, PL-0093, PL-0054 PL-0094, PL-0279 and their respective calibration solutions
I will want to control the timing and power of two Tunze Turbelle in tank pumps and so will need the following cables and splitter: Tunze Kit (includes tunze cables 1&2 with splitter) not sure of order code no I’m guessing PL-0087,Pl-0088 & YL1-2 splitter –please tell!
So far fairly easy!
I also want to be able to stop my main system Eheim return pump (from sump) when the above Tunze pumps are in “feeding mode” what type of plug bar will that plug into? I presume it then needs adding to the programming for feeding ? will that be easy to do?
I have some TMC Aquaray lighting: 3 1500XG tiles and 2 twin Aqua-strip 600’s I will want to dim and time them for sunrise and lunar mode if possible?
I gather that I will need to put a LEDControl-1 between each light and power module, so I will need 4 of these for the 2x twin strips, However the max rating for this GHL item is 700mA at 20V and somewhere I read on a forum it mentioned I would need 2 for each 1000 tile. Please correct me if I’m wrong as the XG1500 tiles are half as much again? and so do they need 3 GHL modules each making a total of 9 plus 4 (for the strips)? How are these connected? It’s important that the tiles are fully powered to get maximum punch/PAR! These items will need power bars digital or analogue? What’s the difference? How many of each will I need?
To future proof I will want the ability to connect later “4” dosing pump, possible a sump LED light, possible GHL storm LEDs and so will need enough sockets for this possibly more Tunze Turbelle pumps !
Obviously a profilux 3 ex based system with a special offer variant - which one ? what how many power bars? Do pumps/ lights that are GHL controlled via special cable need mains power from a power bar or will any socket do?
Lots of questions but difficult to find information that is not confusing!
With all this in mind can you list the order code numbers for me showing the power bars needed and what extras I may need if go for the future bits as well?
Mike