probleme e-mail direct of profilux

[patrick vachon]

I install the new firm ware and soft ware. I try to run the e-mail direct of Profilux but nothing works when I press test. I entered all the same information as on (pc) option, which it works very well.

There you what to do something special for that option (Profilux) email works?

[patrick vachon]

ok, if I go on, system and Lan, I'm on (Obtain IP Automatically) but there are no number?? as 0. is this normal? I thought the ip address of my p3 is a private address, may be the problem??

I do not really know the ip address.:(

I want to send a mail (Hotmail)

[Rival]

patrick, I suppose that your Profilux connected to Lan, is it?

[patrick vachon]

yes!, my p3 is connected with a wire to the router.

[Rival]

Can you connect to your p3 from the PC thru LAN connection?

Probably, your P3 doesn't recieve IP from router (router should assing IP address to P3 by DHCP).

[patrick vachon]

when I connect my p3 to router (lan) router to pc (wireless) pc is laptop

[patrick vachon]

yes i can connect my p3 to my pc whit lan, is what I should try?

[patrick vachon]

IP address of my p3 is the type 192.168.1 ...... I read that hotmail does not accept this type of IP.

How to change IP address of p3??

[Rival]

Ok, for Hotmail the SMTP server is smtp.live.com; (SSL enabled, port 25).
Try configure it with <yourusername>@hotmail.com and password.

[Rival]

you don't need to change IP address on P3 but you can configure NAT on your router.

[patrick vachon]

thank you for the help! here's how I entered the info for direct mail sent p3. and it is the same for (pc) and it works very well

[patrick vachon]

I do all the page of my router, the only place I see is the NAT??

may be the mark of my route the Nome another name?

[Rival]

Yes, it's NAT... but if everything work now, don't change it ;)

[patrick vachon]

well everything works on computer but unable to send a direct mail Profilux??

[boboxx]

the P3 dose not support SSL...

[patrick vachon]

what is the SSL?? how to sent an email on windows live mail?

[Rival]

Hi again,

boboxx is RIGHT, P3 not supports SSL, however live mail required SSL for mail server.

I checked it with live.com and nothing happened but with other smtp account (not required SSL) it's works fine.

But...
other issue that it's not pass probes values :(

That what i got from P3

Temp1: [SENSOR1]
pH: [SENSOR2]
PowerBar-6:[SOCKETS1-8]
$$SENC[1]$$:$$SENV[2]$$

[patrick vachon]

what is possible to send a mail of p3 to hotmail? if you have a way to configure for this to work?

[Rival]

P3 can send mail to any valid email address but I haven’t idea how to use hotmail’s server.
The issue is that P3 not currently support SSL\TLS SMTP authentication method. In this case you can't use hotmail’s server as SMTP sender server.
Probably, you can try to find any other free mail server that not required SSL\TLS.

I got some resources from http://www.emailaddressmanager.com/tips/mail-settings.htm

[patrick vachon]

Ok I managed to send an email on hotmail with option (e-mail notification (Profilux)).

I find it works very well.

Here's how I have make, I opened a account on gmx.com (no need for SSL)

I then entered the info in the notification gmx Profilux.

in a (resipient) you between your Hotmail.

In this way we use the gmx server to send on to Hotmail without SSL.

Here's the info gmx: mailserveur ----------- mail.gmx.com
Port ------------ 587

success

[patrick vachon]

here's how

[Rival]

@ptrick so, could you send any probe value in the email message?

[patrick vachon]

i do not think

[Mathias-Steffen]

To the technical background:
Like already written, PL3 doesnt support SSL (yet) - also we tested a lot of often used mail providers and the difficulty was, that every mail provider uses another smtp-server software working with other communication standards in detail...the newest firmware version should work with all(most) free mail providers as well as custom mailservers.

[Rival]

To the technical background:
Like already written, PL3 doesnt support SSL (yet) - also we tested a lot of often used mail providers and the difficulty was, that every mail provider uses another smtp-server software working with other communication standards in detail...the newest firmware version should work with all(most) free mail providers as well as custom mailservers.

Thank you Mathias.
What about a format to pass to the email message body a probe value. It's work fine with with PLC mail but not with PL3.

[Mathias-Steffen]

We are working hard on the web interface and mail services anyway, just give us a little time please - we will give you information as soon as we are ready with it. :)

[dwsps180]

Any chance the webinterface gets released or beta released this weekend? I love the "change setting" feature for sensors and can't wait to have more controls...especially since I will be on vacation for a few weeks soon.

[GHL Support]

we are working on it

[jamessrich]

any luck on 'email notification profilix' sending probe/state data/info via mail yet?

the only option i have is to send a message no attachment or insert option like on 'email notification pc'

[Matthias]

this is working since 5.05f -> you can insert "tokens" in your email text

the tokens will be evaluated when the email is sent

the tokens are described here:
http://support.aquariumcomputer.com/english/download.php?did=144

[boboxx]

this is the message I have now:
$$ALMS$$

S
$$REPS[32][00]$$ $$SENN[xx]$$ - $$SENV[xx]$$
$$REPE$$

I
$$REPS[32][01]$$ $$ILLN[xx]$$ - $$ILLV[xx]$$
$$REPE$$

S
$$REPS[32][02]$$ $$SWIN[xx]$$ - $$SWIS[xx]$$ [$$SWIC[xx]$$]
$$REPE$$

L
$$LEVN[0]$$ - $$LEVV[0]$$

[Matthias]

thanks C.

we will add a function in PLC6 to insert tokens more easily into the email message