Push Notifications are here!

[Vinny]

The long awaited push notification feature is finally here and ready for prime time. With this new feature you can customize which notifications to receive during alarms, warning events and more. If an alarm is triggered at any moment, the notification will be sent directly to any mobile device which has the GHL Connect app installed.

How to use this new feature:
Make sure your GHL device (starting with ProfiLux 4) is running on the newest firmware along with the newest version of GHL Connect app (3.15.3 (Beta)). Once that is done, you can enable the feature in the app settings page. Next, in the app, press the blue gear icon belonging to your myGHL device connection and enable push notifications for that device. You can now connect to your GHL device however you wish and go to the NETWORK page to configure which notifications to receive.

Combine email and push notifications for the ultimate experience
The more ways your GHL device can reach you, the better Use both features to stay more connected to your aquarium than ever before.

Push notifications will continue to evolve
What we’ve released is not everything that will be offered. Push notifications will be an ever evolving feature that will further expand the way you interact with your aquarium. We have big plans in store (displaying actual sensor values, etc.) and we can’t wait to share it with you!
13022
13023
13024
13025

[EgaReef]

Hi,

Now I can't connect to profilux 4 from the app. I have version 3.13.51 and the one you mention is 3.15.3 which is not on Google Play or on the download page.

What do we do?

Thanks

[Gael]

Hi,

Now I can't connect to profilux 4 from the app. I have version 3.13.51 and the one you mention is 3.15.3 which is not on Google Play or on the download page.

What do we do?

Thanks

Hi,

Firmware 7.25 is required for notifications, 7.28 can be downloaded here: https://www.aquariumcomputer.com/downloads/ghl-control-center-v1-1-3-7/

For the app https://support.google.com/googleplay/answer/7003180 and https://play.google.com/store/apps/details?id=com.aquariumcomputer.GHLConnect

Gaël

[Skydivingcatfan]

I can not figure out how to turn this on. I updated my firmware on my P4 to 7.28 the app on my iPhone is 3.13.5

The instructions say "you can enable the feature in the app settings page" Am i looking at the wrong app settings?

13032

[Gael]

I can not figure out how to turn this on. I updated my firmware on my P4 to 7.28 the app on my iPhone is 3.13.5

The instructions say "you can enable the feature in the app settings page" Am i looking at the wrong app settings?

13032

Hi,

you need GHLConnect 3.15.3 BETA (https://support.google.com/googleplay/answer/7003180)
Beta only available on Android for the moment

Gaël

[Skydivingcatfan]

Thanks

[Nico F.]

I'm probably gonna buy a new profilux 4e starterset next week. Do push notifications also work with the profilux 4e or only the 4?

[Gael]

I'm probably gonna buy a new profilux 4e starterset next week. Do push notifications also work with the profilux 4e or only the 4?

Hi,

The Profilux 4e is a Profilux 4 with the same hardware except for the conductivity input and a Redox/pH port as well as 2 S-Ports:

"In comparison to ProfiLux 4, ProfiLux 4e has in the basic configuration one switchable pH/ORP input instead of two and no conductivity input, and in addition the less required S ports (digital outputs / connection for classicpowerbars) have been removed. Otherwise ProfiLux 4e is identical to ProfiLux 4."

Gaël

[Nico F.]

Gaël,

the differences between 4 and 4e, i'm aware of. It was just to be sure that the push notifications will also work with the 4e.

[Gael]

Gaël,

the differences between 4 and 4e, i'm aware of. It was just to be sure that the push notifications will also work with the 4e.

To be honest I don't have a 4e on hand, but the processor is the same, the firmware is the same, I'm sure notifications will be available.

Gaël

[Vinny]

ProfiLux 4e is included in the push notification feature.

[Nico F.]

I can enable the push notifications in the connect app. But can i check and adjust the settings?
I can only find that i have to disable push notifications and then set it up again?

The notifications are coming through so thats ok.

I also get warning alerts, how do i disable this? I only want the alarms i set up in the connect app, example max level waste container is set to 4500. Now i get a warning alert at a lower level and the red alert at 4500. I don't want the first alarm. This was also so when i didn't had push notifications. The warning tab is off in the push notifications.

[Gael]

I can enable the push notifications in the connect app. But can i check and adjust the settings?
I can only find that i have to disable push notifications and then set it up again?

The notifications are coming through so thats ok.

I also get warning alerts, how do i disable this? I only want the alarms i set up in the connect app, example max level waste container is set to 4500. Now i get a warning alert at a lower level and the red alert at 4500. I don't want the first alarm. This was also so when i didn't had push notifications. The warning tab is off in the push notifications.

Settings are on network page:
https://forum.aquariumcomputer.com/attachment.php?attachmentid=13025&d=1634571291

[Nico F.]

Settings are on network page:
https://forum.aquariumcomputer.com/attachment.php?attachmentid=13025&d=1634571291

Thanks,

That i wouldn't have found :).

Do you know if it's possible to disable warning alerts? I only want the max or low alerts.

[Gael]

Thanks,

That i wouldn't have found :).

Do you know if it's possible to disable warning alerts? I only want the max or low alerts.

13220

[Nico F.]

Thanks again for searching.

That one is off.
But i even did get the warning alerts when i didn't have the P4e.

I had at first a KHD with SA doser unit. I got in app warning alerts, but i don't know id they can be turned of. I only want't the max or low alerts, that's enough for me.

[Nico F.]

Today i installed 2 optical level sensors, version 2 with a splitter cable, purple port.

Sensor 1 is for an alarm sump low level (in dutch : opvoervak laag), which is also written down in the description of level control circuit 1.
If i test the sensor, everything is working ok and i get a push notification : alarm level opvoervak laag.

sensor 2 is for an alarm sump level high (in dutch : opvoervak hoog), which is also written down in the description of level control circuit 2.
If i test the sensor, everything is working ok, only the push notification doesn't give me the correct tekst written down in the description of level circuit 2.
It gives the standard text, alarm level control circuit 2.
So i do get a push notification, which of course is the most important. But not with the correct text.
Anybody got an idea why level 1 gives me the description as push notification and level 2 gives me a standard message?

Not specific for push notifications, but is it possible to disable the warning alarms in the P4e, so the yellow warnings?
I'm only intersted is the critical red alarms.

thanks

Nico

[Vinny]

Nico,

Please open a support ticket to report this issue directly to the GHL team.