PDA

View Full Version : Lots of questions



diltsman
09.01.2019, 04:31
Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?

Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need.

Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?

Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?

Question 5: What kind of flow rate should go through the Measurement Cell?

PIWAWT
11.01.2019, 01:36
Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?
3 for longitudinal mounting

Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need
You can take an LBF-AP to use both pumps.

Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?
yes, you can plug in all three extension cards

Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?
Question 5: What kind of flow rate should go through the Measurement Cell?
Better inflow of the probes, self-cleaning of the probes, longer service life of the probes. The measuring cell is pressureless, if necessary via bypass into the return flow.

regards Pit

diltsman
11.01.2019, 02:47
To clarify, I would use a single LBF-AP and would not need the YL2-1 splitter cable, correct?


Also, do you have an application note or anything about how to plumb the Measurement Cell into a system?

PIWAWT
11.01.2019, 11:25
To clarify, I would use a single LBF-AP and would not need the YL2-1 splitter cable, correct?
yes

Also, do you have an application note or anything about how to plumb the Measurement Cell into a system?

just a simple self-made drawing

11363

regards Pit

Vinny
11.01.2019, 15:01
Hi there,

Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?
This is going to depend on what types of coral you plan to keep and how you will position each fixture; parallel or perpendicular to the tank.

(Perpendicular)
If you have or will have an SPS dominant reef, 5 fixtures would be ideal for the most even light distribution throughout the whole space.
If a mixed reef, 4 fixtures are recommended.

(Parallel or Long way)
SPS dominant: 4 fixtures
Mixed reef: 3 fixtures


Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need.
You would need a 1-10V Breakout box from GHL and the control cable from Coralvue. The RJ45-end of this cable would be cut and installed onto the GHL accessory. Once connected, you will be able to individually control the flow of these pumps.


Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?
Yes.
The P4 includes a total of 3 expansion card slots; 1 slot is for "internal use" which is where you'd connect the PLM-PWC card. The other 2 slots can be for the other cards.


Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?
Measurement cell provides an isolated area which allows for a more constant flow rate and is plumbed into your system, usually in a bypass.
The Sensorholder4 is a magnetic mount that holds the probes out in the open in your sump.


Question 5: What kind of flow rate should go through the Measurement Cell?
A slower flow rate is ideal for this accessory.