PDA

View Full Version : Wireless lan



posts
07.03.2009, 19:51
I can not connect through my WLAN card. I can connect to it directly and look at its configuration which has the right ssid, static IP address, baud rate of 9600 on serial 1 and the baud is set as 9600 on the WLAN serial part of the Profilux. I have set the static IP address in the connection dialog box of the profilux software and if I hit configure it takes me to the cards configuration page.

However, it will never actually connect through the Profilux software. Both the green and red lights on the wlan card are on and the red stays permanently red and does not flicker (which seems suspect to me). My firewall is turned off.

I have a USB serial card installed also. When connected by USB, I can see the WLAN card in the systems section and it appears to accept the SSID and IP address when I type then in here. When I save on the configuration screen, the Profilux gives a message saying it is resetting the module so it can clearly see it.

Any ideas on what might be wrong?

Matthias
09.03.2009, 10:08
can you access the WLAN-card with internet explorer?
(enter IP in the address line of the IE)

posts
09.03.2009, 12:18
Yes I can access it and change any of its properties such as the serial baud rate. Does not appear changing any of these has any affect. The only change seems to be changing the radio management button which seems to mean the red light no longer stays constantly red but starts to flicker (I guess more what I would expect). But in either radio mode I can access the card (I am an IT geek for a living so I am pretty good around wireless networks etc) from IE or Firefox (I think they have a bug with Safari as the card configuration does not display properly)

Regards

Simon



can you access the WLAN-card with internet explorer?
(enter IP in the address line of the IE)

Matthias
09.03.2009, 14:27
The WLAN (and LAN) card uses port 10001 for communication. Is there anything blocking it?
You should not change anything in the Lantronix settings (besides SSID and IP, later the security). If you are not sure what you already have changed -> I recommend to restore the defaults and then go from there.

posts
09.03.2009, 16:20
I can not see anything blocking Port 10001 (firewall is turned off and I have tried XP and Vista) and if I wireshark (packet sniff) the network I can see some IP traffic using SCP-protocol going between my laptop and the wireless lan card on port 10001. Also, not sure if you have seen www.reefiris.com but this allows remote tracking of a Profilux. I can see their website hitting my external router, port forwarding it to the right IP address and port of the wlan card but still not getting a connection with the Profilux.

I have reset the card on several occasions having tried playing with some parameters so I don't think it is card parameters. Is there any log internal to the Profilux I can look at to see if there is a problem with the card talking to the Profilux. I assume it does this over the serial port channel 1?

Simon


The WLAN (and LAN) card uses port 10001 for communication. Is there anything blocking it?
You should not change anything in the Lantronix settings (besides SSID and IP, later the security). If you are not sure what you already have changed -> I recommend to restore the defaults and then go from there.

posts
09.03.2009, 16:22
Also, is there anyway for me to telnet or use some other utility to see whether I can get commands to port 10001 to see if there is some odd block somewhere?

Simon


The WLAN (and LAN) card uses port 10001 for communication. Is there anything blocking it?
You should not change anything in the Lantronix settings (besides SSID and IP, later the security). If you are not sure what you already have changed -> I recommend to restore the defaults and then go from there.

posts
09.03.2009, 21:59
Matthias

Not sure if it will help but I used ReefStatus (thanks xiaan) to see whether it would connect as well and got the following error 'Unable to Read Data packet. A connection attempt failed because the connected party did not properly respond after a period of time or established connection failed because connected host has failed to respond'.

I have also attached the wireshark packet trace if this might shed some light.

Thanks

Simon


Also, is there anyway for me to telnet or use some other utility to see whether I can get commands to port 10001 to see if there is some odd block somewhere?

Simon

Matthias
10.03.2009, 09:11
It is COM2 (COM1 is the built-in RS232) and there you should have 9600 baud.

You can try to use another slot if you think a slot is damaged. But you have no chance to test if the ProfiLux-side of the WLAN-card is working.

But I don't think this is a hardware problem. Did you try a ad-hoc connection as a test?

posts
10.03.2009, 09:29
Yes I have tried an adhoc test and I have tried the card in a different slot. The serial port I was referring to is on the wlan card not the Profilux. Could the USB card be conflicting even though it is not actively connected to the PC software when I am trying to connect through the wlan?

Simon



It is COM2 (COM1 is the built-in RS232) and there you should have 9600 baud.

You can try to use another slot if you think a slot is damaged. But you have no chance to test if the ProfiLux-side of the WLAN-card is working.

But I don't think this is a hardware problem. Did you try a ad-hoc connection as a test?

Matthias
10.03.2009, 09:37
USB and WLAN work together without any side-effects or conflicts. Yes it is COM1 on the WLAN-side.
Summary:
- you are sure that all settings in ProfiLux and your home network are correct
- another slot does not work either
- settings in ProfiLuxControl are correct (BTW: did you try to use "search automatically"?)
- the Lantronix configuration page can be accessed
Correct?
Then the WLAN-card might be defective. Not very likely but not impossible.
If you think the card is damaged then please contact your retailer.

posts
10.03.2009, 16:06
Since I can see the cards setup interface on its IP address (192.168.0.99) and I have checked that COM1 on the WLAN card is at 9600 baud etc, I can't see how it can be a networking problem. To check that somehow port 10001 is not blocked, I have moved COM1 on the WLAN to port 80 and pointed the Profilux Software at port 80 and still no joy. Ergo, don't think it is a networking problem.

Very mysterious. Has anyone else had problems configuring the card? Should I just go LAN rather than wireless or will this change nothing?

Simon


USB and WLAN work together without any side-effects or conflicts. Yes it is COM1 on the WLAN-side.
Summary:
- you are sure that all settings in ProfiLux and your home network are correct
- another slot does not work either
- settings in ProfiLuxControl are correct (BTW: did you try to use "search automatically"?)
- the Lantronix configuration page can be accessed
Correct?
Then the WLAN-card might be defective. Not very likely but not impossible.
If you think the card is damaged then please contact your retailer.

posts
14.03.2009, 14:36
Have purchased a LAN card and it worked straight away. I think there must be something wrong with WLAN card.

Regards


Since I can see the cards setup interface on its IP address (192.168.0.99) and I have checked that COM1 on the WLAN card is at 9600 baud etc, I can't see how it can be a networking problem. To check that somehow port 10001 is not blocked, I have moved COM1 on the WLAN to port 80 and pointed the Profilux Software at port 80 and still no joy. Ergo, don't think it is a networking problem.

Very mysterious. Has anyone else had problems configuring the card? Should I just go LAN rather than wireless or will this change nothing?

Simon

kidney514
14.03.2009, 19:51
Post,

Can you allow me into your router, so that I can look at your router and verify a few things.

if so, enable remote management in your router, put a password and send me your IP address with the password via PM.

To find out what your address is goto: http://whatismyipaddress.com/

It would be helpful in establishing the cause of the problem.

PS After I'm done I will pm you so that you remove the remote management feature and change the password.

kidney514
14.03.2009, 19:51
Post,

Can you allow me into your router, so that I can look at your router and verify a few things.

if so, enable remote management in your router, put a password and send me your IP address with the password via PM.

To find out what your address is goto: http://whatismyipaddress.com/

It would be helpful in establishing the cause of the problem.

PS After I'm done I will pm you so that you remove the remote management feature and change the password.

posts
14.03.2009, 20:16
Unfortunately I have taken the WLAN card out now and replaced it with the LAN card (connected via a wireless gateway). What is it you wanted to look at? I am a pretty technical person and did many tests so I may have checked what you were looking for.

Simon


Post,

Can you allow me into your router, so that I can look at your router and verify a few things.

if so, enable remote management in your router, put a password and send me your IP address with the password via PM.

To find out what your address is goto: http://whatismyipaddress.com/

It would be helpful in establishing the cause of the problem.

PS After I'm done I will pm you so that you remove the remote management feature and change the password.

kidney514
14.03.2009, 23:53
It's ok it's the router itself that I'm curious about......

The wireless mode on your router is set to what?
Mixed B-N-G or
Mixed B-G....
or what was it fixed to when you where trying?

posts
18.03.2009, 21:02
It is an Apple Airport Extreme (in fact several to get coverage throughout my house) running mixed mode B,G and N. Generally had no issues with it for other B/G devices but WIFI is a bit mixed in multi mode environments so could be the problem although seems unlikely since I could reliably connect to the configuration page of the wireless card.

Simon


It's ok it's the router itself that I'm curious about......

The wireless mode on your router is set to what?
Mixed B-N-G or
Mixed B-G....
or what was it fixed to when you where trying?