Activity Stream - GHL Support Forum

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

Today, 19:45

GUPSTER replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

New probe installed ad 18.30 Start temp 24.5 the powerbar is working so my heater is now 1 hour on real tank temp is 25 now but the profilux say...

8 replies | 78 view(s)

Today, 19:15

Manolo_70 replied to a thread in forumdisplay.php?83-Dosieren&s=4766721240721414f093a26da229b9bb

Hallo Gandalf Ich probiere aus. Sollte eigentlich ziemlich einfach gehen. Danke für den Input!

2 replies | 22 view(s)

Today, 19:08

Gandalf replied to a thread in forumdisplay.php?83-Dosieren&s=4766721240721414f093a26da229b9bb

Stell beide pumpen auf die gleiche Geschwindigkeit ein und lass pumpe 2 ebenfalls beim aufhärten mit laufen.

2 replies | 22 view(s)

Today, 18:41

Gael replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

Hello, Never edit calibration values of the temperature sensors: Gaël

8 replies | 78 view(s)

Today, 18:35

GUPSTER replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

New probe is arrived.. Should i change anything in setting. Calibratie data see screenshot

8 replies | 78 view(s)

Today, 18:12

BennySch started a thread in forumdisplay.php?94-ION-Director&s=4766721240721414f093a26da229b9bb

Hallo, Ich habe folgendes Problem. Mein Magnesium Wert passt nicht mit dem gemessenen Wert zusammen. Wenn ich mit dem Multi-Reference messe,...

0 replies | 12 view(s)

Today, 14:29

Manolo_70 started a thread in forumdisplay.php?83-Dosieren&s=4766721240721414f093a26da229b9bb

Hallo zusammen Ich plane den wöchentlichen Austausch von Aquariumwasser mit Leitungswasser zu automatisieren. Ziel ist es einen konstanteren...

2 replies | 22 view(s)

Yesterday, 19:20

mrtxxx started a thread in forumdisplay.php?82-Customer-s-wishes&s=4766721240721414f093a26da229b9bb

Hi, My request will certainly be directed on behalf of many aquarists, namely the lack of the ability to show salinity in the SG unit - Specific...

0 replies | 31 view(s)

Yesterday, 18:47

Gael replied to a thread in forumdisplay.php?94-ION-Director&s=4766721240721414f093a26da229b9bb

Hallo Timos, Ich verstehe Ihre Ungeduld. wie bereits geschrieben, sobald wir konkrete Informationen über die Verfügbarkeit haben, werden wir dies...

4 replies | 284 view(s)

Yesterday, 18:16

Vinny replied to a thread in forumdisplay.php?93-KH-Director&s=4766721240721414f093a26da229b9bb

Remove the probe from the KHD and inspect the teeth on the compression fitting. If any are bent or damaged, it will not create a tight seal around...

1 replies | 42 view(s)

Yesterday, 17:49

Timos Riff replied to a thread in forumdisplay.php?94-ION-Director&s=4766721240721414f093a26da229b9bb

Hallo GHL, könnt ihr absehen, bis wann die Sensoren wieder lieferbar sind? Im Dezember habt ihr geschrieben zuversichtlich zu sein, noch dieses Jahr...

4 replies | 284 view(s)

Yesterday, 12:22

Gael replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

For P3: PL-0094 https://store.aquariumcomputer.com/en/product_info.php?info=p44_temperature-sensor-aquarium.html (Or PL-0538 for measurement in...

8 replies | 78 view(s)

Yesterday, 12:07

GUPSTER replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

LSF .. he told me that the mini din connector pt1000 are old. And that i could use the one with bnc connector but have to switch connector.. Il...

8 replies | 78 view(s)

Yesterday, 11:39

Gael replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

New from where? GHL temperature sensors with BNC connector are not PT1000 but digital chip. Gaël

8 replies | 78 view(s)

Yesterday, 11:33

GUPSTER replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

Do you know how much Ohm te probe should have Wen masure the probe is like 650 Ohm at 25 degrees I brought a New one but its a BNC connector....

8 replies | 78 view(s)

Yesterday, 11:19

Gael replied to a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

Hello, Sorry for that, but i guess sensor may be a little old. The sensor may be broken yes, check also the wiring, there may be a bad contact at...

8 replies | 78 view(s)

Yesterday, 10:45

GUPSTER started a thread in forumdisplay.php?18-Heating-and-cooling&s=4766721240721414f093a26da229b9bb

profilux 3.1 ex My temperature management went perfectly But now my temperature sensor is upset .. temperature suddenly rises according to the...

8 replies | 78 view(s)

29.01.2023, 22:37

kelpforests started a thread in forumdisplay.php?93-KH-Director&s=4766721240721414f093a26da229b9bb

My Ph probe is very slightly leaking after replacing for calibration. The nut and gasket are not damaged or cracked. I have closed it as tight as I...

1 replies | 42 view(s)

29.01.2023, 11:54

PIWAWT replied to a thread in forumdisplay.php?2-Messen-und-Regeln&s=4766721240721414f093a26da229b9bb

Bei einem ist der Sensor auf Süsswasser (nicht-eX), beim anderen (eX) auf Meerwasser eingestellt Gruss Pit

1 replies | 48 view(s)

29.01.2023, 11:39

Troubadix started a thread in forumdisplay.php?2-Messen-und-Regeln&s=4766721240721414f093a26da229b9bb

Hallo, nachdem ich durch die Falschlieferung auf das Thema Leitwert gestoßen wurde hab ich mir da mal zum Spaß die Einstellungen angeschaut. Ich...

1 replies | 48 view(s)

29.01.2023, 11:24

Troubadix replied to a thread in forumdisplay.php?2-Messen-und-Regeln&s=4766721240721414f093a26da229b9bb

Danke, das Problem wurde via Ticket bearbeitet

4 replies | 128 view(s)

29.01.2023, 07:29

Gael replied to a thread in forumdisplay.php?85-myGHL&s=4766721240721414f093a26da229b9bb

Hallo, ich habe das Problem gerade reproduziert. Es gibt tatsächlich ein Problem mit GHLConnect 3.22.13, wenn Sie sich direkt lokal mit einem...

1 replies | 64 view(s)

29.01.2023, 05:46

argileh replied to a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

Thank you.

2 replies | 53 view(s)

29.01.2023, 05:17

Gael replied to a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

Hello, GCC 1.1.4.3 including firmware 1.15 is not yet published, it will be in next days. Gaël

2 replies | 53 view(s)

29.01.2023, 05:04

argileh started a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

Yesterday (28 January 2023) I received an email notification from GHL that the new ProfiLux Mini/Light ATO/autofeeder adapter is now available for...

2 replies | 53 view(s)

28.01.2023, 23:13

Dave_T replied to a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

The PLM-ADIN card is in an expansion box. If I reboot the expansion box, the digital inputs remain active. But if I reboot the Profilux, they do...

14 replies | 89 view(s)

28.01.2023, 21:54

Gael replied to a thread in forumdisplay.php?11-Illumination-control&s=4766721240721414f093a26da229b9bb

Hello, Simusticks are operated in 1-10v while the Mitras LB are operated via the Mitras port, just be sure to assign to corresponding 1-10v...

1 replies | 34 view(s)

28.01.2023, 21:50

Gael replied to a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

This is not normal. However, if you restart the ProfiLux electrically, the inputs return to inactive? Gaël

14 replies | 89 view(s)

28.01.2023, 21:39

cajburgers started a thread in forumdisplay.php?11-Illumination-control&s=4766721240721414f093a26da229b9bb

I'm trying to make a nice light display (with a "dip"in the middle, around mid-day) I have 2 simusticks and 4 mitras daylights (2x60cm and...

1 replies | 34 view(s)

28.01.2023, 21:28

Dave_T replied to a thread in forumdisplay.php?9-Measuring-and-controlling&s=4766721240721414f093a26da229b9bb

I'm testing it by connecting the digital input pin directly to the GND pin on pin 8, with alligator clips. That's fine, right? If I refresh the...

14 replies | 89 view(s)