Page 17 of 18 FirstFirst ... 715161718 LastLast
Results 161 to 170 of 173

Thread: Firmware-Update für EHEIM-Filter

  1. #161
    Join Date
    11.01.2016
    Posts
    1

    Default

    Sorry for the English, I am from Sweden, I understand German but is really bad in writing.
    I have a Eheim 2078 who constantly run I calibration mode if I try to run it I high flow rates, at low rate it runs OK.
    I have checked everything in the pipes and filter, can't find any problem.
    Can a firmware upgrade solve this problem? I'm running 4.0 in the filter now. See attached print screens.
    I have found the files in this sides download area but I need a password for the zip file.

    Best regards
    Peter

    Filter type.jpg
    Filter fw.jpg

  2. #162
    Join Date
    06.02.2012
    Posts
    2,020

    Default

    Can a firmware upgrade solve this problem?
    The firmware update provided here is an update to solve/prevent problems for a combination of the Eheim filter with the GHL Eheim controller.
    I´m afraid it will not change anything for you.

  3. #163
    Join Date
    03.02.2016
    Posts
    2

    Default

    Hallo, bitte um Zusendung der beiden Updates, Filter 2078 und Interface. Besten dank. Fachleute@web.de

  4. #164
    Join Date
    03.02.2016
    Posts
    2

    Default

    ...leider habe ich noch keine Nachricht bezüglich Updates erhalten, würde mich freuen von euch zu hören. Updates Filter 2078 und Interface wird benötigt.

  5. #165
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    alles im Downloadbereich zu finden
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  6. #166
    Join Date
    09.06.2013
    Posts
    100

    Default

    Hallo,die ZIP-Datei im Downloadbereich https://www.aquariumcomputer.com/dow...e-update-tool/ erfordert ein Passwort.
    Wo bekommt man dieses her?

  7. #167
    Join Date
    24.07.2016
    Posts
    6

    Default

    Hi, could i have the password for the update zip file? Thank you!

  8. #168
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    Hi

    I updated this file, I was able to open it without a password.

    Please check and let me know if it works.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  9. #169
    Join Date
    24.07.2016
    Posts
    6

    Default

    Now it opens without a password. Thank you!

  10. #170
    Join Date
    17.11.2016
    Posts
    3

    Default

    Hallo. Was kann mit dem Filter falsch sein? Von Anfang an es kalibriert es selbst (i versucht Reset). Der Filter wurde gereinigt und alle Dichtungen sind ok (kein Lecken und keine Luft im Filter). Dieses Problem ist nur in konstanten Fluss, aber in Bio-Stream und 12h Bio-Funktion das Programm wird nicht starten, LED zeigt, dass Programm läuft aber Flow ist fix auf 1170l / h (leere Körbe). Bei leeren Körben im manuellen Betrieb läuft der Filter OK und ich bekomme 1439l / h Durchfluss.

    Ich versuchte neue Firmware 6.1 aber das Problem ist immer noch da. Ich allso versucht difrent eletronic von anderen 3e 2078 aber das Problem ist das gleiche.

    Mit freundlichen Grüßen
    Robert

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •