Results 1 to 6 of 6

Thread: Expansion Box 1 configuration error with P4

  1. #1
    Join Date
    10.10.2013
    Posts
    994

    Default Expansion Box 1 configuration error with P4

    Hi,

    I get "The PAB device is not responding!" when i press "Configuration" on Expansion Box V1 with Profilux 4.

    I done RAZ PAB and only assigned the expansion Box and after Configuration Button is ok.

    BUT after assigned all my other PAB device i get again the error:

    Capture d’écran 2018-03-02 à 14.58.15.jpg

    ***** System report *****
    Controller properties
    Name: ProfiLux 3.1T eX
    Firmwareversion: 6,32
    Device address: 2
    PAB address: 17
    Slot count: 3
    Level inputs: 4
    Sensor 1: pH-value
    Sensor 2: Temperature
    Sensor 3: Conduct.(S)
    Sensor 4: Redox
    Onboard 1-10V outputs: 6
    Onboard socket outputs: 8

    Slot/card properties
    Slot number 0
    Name: SERIAL
    Class: Communication card

    Slot number 1
    Name: 2L4S
    Class: Intelligent card
    Firmwareversion: 1,00
    1-10V outputs: 2
    Socket outputs: 4

    Slot number 2
    Name: PWC
    Class: Communication card


    PAB devices
    Name: SMS-Module
    Firmwareversion: 3,04
    PAB-address: 19

    Name: Expansion Box
    Firmwareversion: 1,08
    PAB-address: 18

    Name: VorTech-Controller
    Firmwareversion: 1,04
    PAB-address: 20

    Name: ProfiLux Touch
    Firmwareversion: 1,06
    PAB-address: 21

    Name: GHL Doser 2 Slave
    Firmwareversion: 1,27
    PAB-address: 22

    Name: GHL Doser 2 Slave
    Firmwareversion: 1,27
    PAB-address: 23

    Name: KH Director
    Firmwareversion: 1,00
    PAB-address: 24

    Thank

  2. #2
    Join Date
    07.04.2017
    Posts
    157

    Default

    From my experience you have to have only the EXP connected as a PAB device for the configuration button to work.

  3. #3
    Join Date
    10.10.2013
    Posts
    994

    Default

    um ... ok thank you, it seemed to me that with the P3 we could, but I'm probably wrong.

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    Configuration should also work when all PAB devices are assigned.
    Maybe it depends on the number of connected devices. I will check this for a future update.

    But for now it is solved, you were able to configure it?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    10.10.2013
    Posts
    994

    Default

    Yes Matthias, as wrote i I done RAZ PAB and only assigned the expansion Box and after Configuration Button is ok.
    After that i re-assigned all my other PAB device.

    Thank

  6. #6
    Join Date
    03.05.2012
    Posts
    227

    Default

    Quote Originally Posted by itsmorefun View Post
    Yes Matthias, as wrote i I done RAZ PAB and only assigned the expansion Box and after Configuration Button is ok.
    After that i re-assigned all my other PAB device.

    Thank
    Yup can confirm that on 7.12 this is the behavior if you want to config the Expansion Box you have to unassigned all other PAB devices, configure the Expansion Box ( ver. 1) then reassign the other PAB devices. Hope this gets sorted soon.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •