Results 1 to 8 of 8

Thread: Lost operating hour meter

  1. #1
    Join Date
    28.05.2017
    Posts
    33

    Default Lost operating hour meter

    My operating hour meter count was reset on the switch channels after todays firmware upgrade to 7.10.
    How can i restore them? I thought they where saved with the settings save...
    Last edited by Thidsa; 05.01.2018 at 20:29.

  2. #2
    Join Date
    07.02.2017
    Posts
    26

    Default

    Same here. All reset to zero.

  3. #3
    Join Date
    28.05.2017
    Posts
    33

    Default

    Yes, i know some of the numbers to a certain degree. and i like to get them back. Better a little off then 0. Someone must know how to restore them....

  4. #4
    Join Date
    07.04.2017
    Posts
    157

    Default

    Remember the sensor settings and the regular settings are two exports. Did you import both or the backup files?

  5. #5
    Join Date
    28.05.2017
    Posts
    33

    Default

    yes both. so it should be restored if the data is stored in the backup. Anybody knows if it is?

  6. #6
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    the operation hour meter were not saved in previous versions

    this has been changed now for all backups starting with firmware 7.10

    but if you know your numbers there is a trick:

    1. save all your settings with newest GCC

    2. open the settings file with text editor (e.g. notepad)

    3. search for these lines:
    10284, "CODE_PROFILUX4_SP1_OHM - 0 - 0", 20477
    10285, "CODE_PROFILUX4_SP1_OHM - 0 - 1", 17193
    10286, "CODE_PROFILUX4_SP1_OHM - 0 - 2", 0
    10287, "CODE_PROFILUX4_SP1_OHM - 0 - 3", 0
    10288, "CODE_PROFILUX4_SP1_OHM - 0 - 4", 30
    10289, "CODE_PROFILUX4_SP1_OHM - 0 - 5", 27252
    10290, "CODE_PROFILUX4_SP1_OHM - 0 - 6", 765
    10291, "CODE_PROFILUX4_SP1_OHM - 0 - 7", 27252
    10292, "CODE_PROFILUX4_SP1_OHM - 0 - 8", 0
    10293, "CODE_PROFILUX4_SP1_OHM - 0 - 9", 14589
    10294, "CODE_PROFILUX4_SP1_OHM - 0 - 10", 17193
    10295, "CODE_PROFILUX4_SP1_OHM - 0 - 11", 27252
    10296, "CODE_PROFILUX4_SP1_OHM - 0 - 12", 14589
    10297, "CODE_PROFILUX4_SP1_OHM - 0 - 13", 27252
    10298, "CODE_PROFILUX4_SP1_OHM - 0 - 14", 27252
    10299, "CODE_PROFILUX4_SP1_OHM - 0 - 15", 0
    ... etc.

    these are the OHM for all 64 sockets

    3. the last number is the time in hours - change them, save the file

    4. load this file back to P4

    -> we add the option to modifiy these numbers in a next GCC version
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  7. #7
    Join Date
    28.05.2017
    Posts
    33

    Default

    Yes ! Thanks Matthias
    Thats was the answer i was looking for
    Great

    PS. Noticed the number was the time in minutes
    Last edited by Thidsa; 17.01.2018 at 17:06.

  8. #8
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    you are right, my mistake
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •