Zeige Ergebnis 1 bis 9 von 9

Thema: HOW to control 1 Tunze stream 3 (6150) and two 6105 ?

  1. #1
    Registriert seit
    16.11.2010
    Ort
    Amiens
    Beiträge
    24

    Standard HOW to control 1 Tunze stream 3 (6150) and two 6105 ?

    Hi,
    i'm coming to you to get answer and know the best way to connect the new stream 3 (6150) with two 6105.
    Actually i run with 4 x 6105 but as i get the 6150, i'd like to run now (before buying another one :-) ) with two of my 6105.

    Q1: can i put the two stream 1 & 2 with the Y splitter on the L1L2 and the stream 3 directly on the L3L4?
    Q2: do i had to change the voltage? what is it by the way? for the 6105 it was (3 to 8 v) not 0-10V
    Q3: what's gonna be the best programs for all? I'd like the 6150 work alone for 6 hours and then the 6105 for 6 hours and so on

    thx by advance

  2. #2
    Registriert seit
    27.05.2015
    Beiträge
    985

    Standard

    Hi there,

    1. Yes, of course. The splitter cable you would need to do this is the YL2-cable. The Stream 3 pump can be connected directly to the L3/L4 port without a problem. In this scenario, the L-channel that would be assigned to the Stream 3 pump would depend on the Tunze cable you are using. If you will be connecting the pump with a Tunze 1 cable, it would be assigned to L3. If it is connected with a Tunze 2 cable, it would be assigned to L4.

    2. Same voltages apply for the Stream 3 pumps, 3-8v.

    3. This cannot be answered easily as there are too many variables to consider; rockscape layout, tank length, pump min/max speed, etc. In order to turn one pump on for 6 hours, then another for 6 hours, use one of the SEQUENCE mode options. You can find more information on this mode in our P4 Programming Guide, page 36.

  3. #3
    Registriert seit
    16.11.2010
    Ort
    Amiens
    Beiträge
    24

    Standard

    Ok, i'm gonna try that
    thx vinny, always good and quick advices from you
    For the 6150 program i've put sinuswave 10/40s for the moment
    and the two 6105 on sequence1 without wave
    i'll see
    thx again

  4. #4
    Registriert seit
    03.03.2009
    Ort
    alingsås
    Beiträge
    116

    Standard

    I have the same ”problem” but how can I see the diffrent of the tunze cabel, the cabels is old and have no labels with tunze 1 or tunze 2




    Skickat från min iPhone med Tapatalk

  5. #5
    Registriert seit
    27.05.2015
    Beiträge
    985

    Standard

    If there are no labels on your cables, you will need to pick one cable and try it on an odd numbered L-channel. If it successfully controls the Tunze pump, the cable is a Tunze 1. If it reacts to an even-numbered L-channel, it is a Tunze 2.

  6. #6
    Registriert seit
    03.03.2009
    Ort
    alingsås
    Beiträge
    116

    Standard HOW to control 1 Tunze stream 3 (6150) and two 6105 ?

    Okey
    Some more help

    In the meny 1-10 interface
    Is 1 the same as L1
    2 as L2 etc

    I try to it work but the pump still run

    I have a old ghl 2
    FW 5.17




    Skickat från min iPhone med Tapatalk

  7. #7
    Registriert seit
    16.11.2010
    Ort
    Amiens
    Beiträge
    24

    Standard

    Now i have two 6150
    I put two hours each pump in sequence 1 with wave 10/60s
    The 1-10v interface stay at 3-8v BUT:
    my pump only goes at 80-81% when there are at maximum SO
    Should i put it at 1-10v instead?
    thx

  8. #8
    Registriert seit
    27.05.2015
    Beiträge
    985

    Standard

    Make sure the dial on the Tunze controller is also set to full power.

  9. #9
    Registriert seit
    07.04.2017
    Beiträge
    138

    Standard

    Zitat Zitat von Vinny Beitrag anzeigen
    Make sure the dial on the Tunze controller is also set to full power.
    Is it a reason why the Stream 3 should be 3-8v, not 0-10v? I cant find any reference to 3-8 from tunze?

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •