Search:

Type: Posts; User: JamesD

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    3,797

    Thanks Vinny. After issues with my old silicone...

    Thanks Vinny. After issues with my old silicone dosing lines I was thinking of changing all of the lines to this including my non KHD doser.
  2. Replies
    2
    Views
    3,797

    New tube diameter and specification

    Hi

    Is the replacement doser tube which is supposed to stop the bubble problem still 4mm internal diameter please?

    Also what type of tube/specification/material is it please as I would like to...
  3. Replies
    14
    Views
    8,482

    How about starting a test from the Profilux...

    How about starting a test from the Profilux Touch? ( I assume this can not already be done?)
  4. Replies
    3
    Views
    2,044

    Thanks Mattias I am not clear-should I add the...

    Thanks Mattias

    I am not clear-should I add the 150mm length of the white dosing head tubing to the total sample tubing length please?

    Also if the sample tubing sits under water should I take...
  5. Replies
    14
    Views
    8,482

    Sorry battery went dead before posting

    I haven’t used it long enough but having recently set it up I have a few suggestions for accessories
    1-Branded dosing containers for reagent and waste/overflow-waste being much bigger than the...
  6. Replies
    14
    Views
    8,482

    My suggestions are simple ones: A colour...

    My suggestions are simple ones:
    A colour coordinated stand the same size as the doser/KHD to lift it up slightly s
  7. Replies
    3
    Views
    2,044

    KHD setup questions please

    1- aeration of KHD solution tube. First disconnect from KHD and fill tubing using manual pump controls until it is full ie including the short pipe out of the doser head; then connect to KHD...
  8. Replies
    1
    Views
    2,007

    KHD and doser set up

    Hi

    I have currently have a P4, and a standalone doser 2.1SA dosing Triton, but it is not connected to the P4. I have bought a KHD and another doser 2.1 SA to dose the KH.

    I want to daisy...
  9. Replies
    2
    Views
    1,811

    Cut and reconnect level sensor cable?

    My skimmer keeps overflowing and I would like to add a level sensor to the skimmer cup, but I don't want to drill a bigger hole to fit the standard plug through. Could I cut and reconnect the cable...
  10. Anyone controlled window blinds, curtains, drapes with Profilux?

    I would like to close window blinds based on tank temperature. Has anyone done this? If so what product did you use for the blinds? I was thinking something like Somfy controllers where the...
  11. thanks for the advice.

    thanks for the advice.
  12. Doser 2.1 SA setup as slave compared with doser 1

    I'm waiting for my doser 2.1 SA which I want to set up as a slave (although dosing Triton method I am not sure of the advantages, so may use stand alone). Anyway is the set up the same as doser 1 as...
  13. Replies
    50
    Views
    29,182

    Micro bubbles

    My old P3 conductivity, connected to my P3, stays constant but the new P4 probe readings fluctuate , but if I take the new P4 one out and put it back in the water it is ok. Therefore I think it is,...
  14. Replies
    1
    Views
    1,487

    Dennerle Trocal delete with Mitras

    I have this listed in my GCC in the left hand list of devices, as my P3 was second hand. I run Mitras and have a separate icon for this.. Can I delete Dennerle Trocal and how is this done please?
  15. Thread: temp probe bug

    by JamesD
    Replies
    10
    Views
    5,637

    did you resolve this? I had the same issue with...

    did you resolve this? I had the same issue with the probe my P4 came with. I swapped it for another temperature probe and it worked ok i.e. read similar to there thermometers in the sump.
  16. Replies
    50
    Views
    29,182

    Same issue with fluctuating salinity

    i have a similar issue with the conductivity probe, jumping around by a significant amount. Yes, it may be the effects of micro bubbles, but if that is the case, why is my old P3 probe which is...
  17. Replies
    1
    Views
    2,493

    Doser 1 calibration

    Having problems working out how to calibrate my second hand doser 1. I'm connected via wifi to Profilux 3.1. Flowrate says 50 ml/ minute but if I press calibrate the pump now it only runs for a few...
Results 1 to 17 of 17