Suchen:

Art: Beiträge; Benutzer: ReefClownMIA

Seite 1 von 2 1 2

Suchen: Die Suche dauerte 0,00 Sekunden.

  1. Antworten
    3
    Hits
    118

    Ahh, yes - the hanging kits became optional due...

    Ahh, yes - the hanging kits became optional due to customer feedback some time ago, including the 6X00's.
    Many customers mount the lights via alternate ways and found the prepackaged hanging kit...
  2. Antworten
    4
    Hits
    226

    While the alternating ramp of the pumps is...

    While the alternating ramp of the pumps is possible, via the Stream Groups, there is not a tie-in to the Stream groups from the Flow Sensor. The flow sensor is set to a static value, and will...
  3. Antworten
    1
    Hits
    74

    LX7's have the Power Balancing, this is a...

    LX7's have the Power Balancing, this is a hardware feature, not software
  4. Antworten
    3
    Hits
    118

    hmmnn. Not sure what you mean with the Support is...

    hmmnn. Not sure what you mean with the Support is not included like the 6200's. :/
  5. Antworten
    10
    Hits
    248

    Have you cleaned it, then reset and moved...

    Have you cleaned it, then reset and moved up/down, above and below water to see if it shows reaction in GCC under "SETTING AND STATES LEVEL-SENSOR INPUTS"
    I'm just going to throw this out there,...
  6. I'm using a Madison submicro floatswitch on an...

    I'm using a Madison submicro floatswitch on an ADIN card, works a treat!
  7. Antworten
    2
    Hits
    111

    Hi, ja nach dem umstellen erst speichern, dann...

    Hi, ja nach dem umstellen erst speichern, dann Kalibrieren. Ansonsten kalibriert das mit der vorherigen gespeicherten Einstellung.
  8. Antworten
    10
    Hits
    248

    Have you toggled the sensor(s) to see if they...

    Have you toggled the sensor(s) to see if they respond in GCC ?
    Can you post a screenshot of your ATO configuration showing the sensors?

    Also make sure that your cables are connected snug, if...
  9. Antworten
    4
    Hits
    226

    I can't think of any way to make this work with...

    I can't think of any way to make this work with the flow sensors, as they are not ramp-able. The flow rate on the flow sensors is statically set, and will maintain the flow at said rate.

    What you...
  10. No worries at all - happens to the best of us. :)

    No worries at all - happens to the best of us. :)
  11. Antworten
    10
    Hits
    301

    You mentioned that you use RO style fittings, and...

    You mentioned that you use RO style fittings, and looking at the power plugs looks like you're in Europe(for now) - UK?
    Here in the US many consider John Guest fitting as "RO style" fittings - these...
  12. Make sure you're using the correct FIRMWARE...

    Make sure you're using the correct FIRMWARE update mode, and not the PAB Device update.

    Here is the HowTo video, just as a refresher :)

    https://www.youtube.com/watch?v=Fj0SH93QoKc
  13. Antworten
    1
    Hits
    367

    Yes, this is possible with a 0-10v controllable...

    Yes, this is possible with a 0-10v controllable return pump.
    https://www.reef2reef.com/threads/flow-sensors-usage-and-example-setup.261199/
  14. Antworten
    16
    Hits
    983

    Correct, v1.0.9.9 & fw 7.07 contain the email...

    Correct, v1.0.9.9 & fw 7.07 contain the email notifications.
  15. Antworten
    18
    Hits
    693

    What country, and ISP are you on?

    What country, and ISP are you on?
  16. Sounds like your LFS ordered an upgrade kit for...

    Sounds like your LFS ordered an upgrade kit for the Doser 2.
  17. Antworten
    3
    Hits
    261

    Hi Lincsreefer, A couple of questions: When...

    Hi Lincsreefer,

    A couple of questions:
    When you say you have ports forwarded etc, are you accessing the PL4 from a remote network/location? Over the internet?
    What is your PL4 firmware and WiFi...
  18. Hi Jay - have a look at this, was posted on one...

    Hi Jay - have a look at this, was posted on one of the prior pages in this thread.
  19. Antworten
    16
    Hits
    983

    Hi Bandit, GHL does not provide dates prior to...

    Hi Bandit,
    GHL does not provide dates prior to release, to avoid disappointing expectations.
    GHL is however working on it diligently. All of the updates go through extensive testings, this...
  20. Antworten
    1
    Hits
    160

    I can't speak to the feature request, however...

    I can't speak to the feature request, however this can be done via MyGHL web interface which would be available from smartphone/tablet as well :)
  21. Antworten
    13
    Hits
    1.117

    This is the idea - same here :) I'm a huge fan...

    This is the idea - same here :)
    I'm a huge fan of varying the lighting, to not be static.


    Define Sunrise/Sunset? What is it that you're expecting, vs what you're getting now?


    lighting, or...
  22. Jose, Your complaints have been duly noted,...

    Jose,
    Your complaints have been duly noted, let's lay them to rest though. That way everyone can go back to work and be productive, bringing the features you're missing, rather than responding to...
  23. I must ask, other than Android and iOS App and...

    I must ask, other than Android and iOS App and Internet server - what "performance" did the P3 offer that makes you feel that the P4 is a "half-cooked cake" ?
    While I'll agree that the release of...
  24. The simplest way would be by running a PAB cable...

    The simplest way would be by running a PAB cable from the P4 in the basement, to your display upstairs. There you would place an expansion box.
    The Expansion box will allow connection of 2x level...
  25. Antworten
    1
    Hits
    300

    The default port for GCC to connect on is 10001...

    The default port for GCC to connect on is 10001
    This should be pre-filled when you change from USB to Network (TCP/IP)
Zeige Ergebnis 1 bis 25 von 42
Seite 1 von 2 1 2